Ele ADR Touch Advanced Readout US Edition Operating Instructions Manual Download | Manualshive

Page: 12 / 12

background image

ADR Touch Advanced Readout US Edition

37-4856/09

Original Instructions

12

9901X0277 Issue 3

Fuse failure is typically caused by an instrument problem. If the fuse continues to fail, contact

ELE International’s Customer Service Department.

A spare fuse is supplied in the fuse drawer. Refer to Section 1 Specifications for fuse

requirements.

a. Set the power switch for the controller to off.

b. Remove the power cord for the controller from the electrical outlet.

c. Use a flat-blade screwdriver to open the fuse drawer.

d. Remove the fuse drawer and replace the fuse.

e. Install the fuse drawer.

7

Troubleshooting

7.1

Common problems

«
...
10
11
12

Summary of Contents for ADR Touch Advanced Readout US Edition













Reviews:

No comments

Related manuals for ADR Touch Advanced Readout US Edition

Brand: Daavlin Pages: 13

Brand: Daavlin Pages: 27

Brand: Baker Instrument Company Pages: 24

Brand: Labnet Pages: 5

Brand: Labnet Pages: 2

Brand: Oberheim Pages: 40

Brand: VeEX Pages: 2

Brand: JB-Lighting Pages: 48

Precision2 HP2 Series

Brand: B-K lighting Pages: 6

Brand: Zero Hand Truck Pages: 38

Brand: B-K lighting Pages: 3

Brand: p-light Pages: 28

SimMan 3G Trauma

Brand: laerdal Pages: 16

Brand: laerdal Pages: 16

Brand: laerdal Pages: 60

Brand: laerdal Pages: 4

Resusci Anne Simulator

Brand: laerdal Pages: 8

Nursing Baby VitalSim

Brand: laerdal Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands