SOI ONE User Guide
Datasheet support@elecfreaks.com
3
5
、
Real-time temperature of the soldering iron. ERROR occurs when unconnected, and it only
shows real-time iron temperature when the soldering iron is inserted.
5.
Menu
中文
English Korean
设置菜单
Main menu
메인메뉴
┣基本设置
Base setup
기본셋팅
┃┣运放增益
Amplify gain
증폭계수
Default value 239, range 100-350, change unnecessary
┃┣失调电压
Amplify offset
실조전압
Default value 50, range 0-400mv, change unnecessary
┃┗热电参数
Thermocouple
열전
계수
Default value 42, range 30-50, adjust when screen
temperature is different from real-time temperature
┣待机设置
Standby setup
절전설정
┃┣
待机
温
度
Standby temp
온도설정
Default 200
°C, range 180-250
°C
┃┣待机时间
Idle time
초과
시간
Default 2 minutes, range 1-30 minutes
┃┗唤醒模式
Wakeup mode
동작방법
(
编码
/
震动
) (KNOB/SHAKE) (
핸들
/
진동
)
┣休眠设置
Sleep setup
수면
설정
（
Sleep mode, heating stops
）
┃┗休眠时间
Poweroff time
초과
시간
Default 5 minutes, range 0-30 minutes
┣加强设置
Boost setup
강화설정
┃┣增加温度
Boost temp
온도강화
range 20-100
°C, Default 50
°C
┃┗加强时间
Boost time
시간강화
Default 1 minute, range 1-10 minutes
┣步进设置
Stepping temp
스텝
온도
Default 10°C, range 1-10°C
┣屏幕设置
Screen setup
화면설정
┃┣标题位置
Title line
표제위치
(
上
/
下
) (TOP/BOTTOM) (
상
/
하
)
┃┗屏保时间
Saver ActTime
대기시간
Default 15 seconds, range 0-240 seconds. Saver off at 0
second.
┣蜂鸣设置
Buzzer setup
알람설정
┃┣蜂鸣开关
Sound enable
알람사용
(
关
/
开
) (OFF/ON) (
정
/
부
)
“on/off”, default off
┃┗提醒方式
When to beep
알람
방식
(Save/All) (
저장
/
전부
)
┣恢复默认
Factory reset
초기화
(
是
/
否
) (Confirm/Cancel) (
정
/
부
)
┣电压设置
Power monitor
전원설정
┃┣
蜂
鸣电压
Alarm voltage
경고
전압
Default 14V, range 4-20V. Alarm voltage off at 4V.
┃┗休眠电压
Poweroff volt
차단전압
Default 12V, range 4-20V. Poweroff volt off at 4V.
┣调试信息
Debug Mode
검사모드
(
关
/
开
) (OFF/ON) (
정
/
부
)
┗开机全屏
Boot SCN test
화면
검사
(
关
/
开
) (OFF/ON) (
정
/
부
)
The screen is white when
booting and you can tell if OLED is damaged.
6.
Basic operation
1
：
Turn down temperature by switching counterclockwise (minimum 180°C), turn up clockwise
(maximum 430°C
）
2
：
Go to boost mode by briefly pressing the encoder and the temperature on the screen will
