background image

2

 

STANDARD EQUIPMENT 

Electric Eel Model RF comes complete with: 

RF unit with auto cable feeder

Cable guide spring

100 ft. of 3/4” Tri-Max

 

Cable

Set of 

3

 cleaning tools including:

!

A-1DC starting drill

!

U-3H grease tool

(U-cutter)

!

HDD-3S root saw

1-FLSC1SC2 flexible leader

SC-18 spanner wrench

Tool bag to hold cleaning tools

SAFETY  

INSTRUCTIONS 

The  following  safety  rules  for  operating 

Electric  Eel’s  Sewer  and  Drain  Cleaning 
equipment 

MUST

  be  read  carefully 

before operating this machine. 

GENERAL SAFETY 

   

DANGER 

TO PREVENT SERIOUS BODILY 

INJURY: 

1.

ALWAYS

 wear 

HEAVY

 leather

gloves and safety glasses when
operating equipment.

2. Place machine cable guide spring

at pipe opening.  

NEVER

 have

exposed cable.

3.

DO NOT

 wear loose clothing or

jewelry while operating this
machine.

   

DANGER 

To prevent serious injuries including: 

Shock, electrocution or burns due
to improper grounding.

Serious injuries to body, limbs or
hands and feet due to cables that
twist, kink and break.

Eye injuries caused by loose cable,
thrown debris or splashed water.

READ SAFTEY INFORMATION 

THOROUGHLY! 

Summary of Contents for RF









Reviews: