background image

 

FIRST USE 

IMPORTANT

Before using the scooter for the first time, fully charge the battery. After 

turning on the scooter, check the battery power on the display and verify that all lights are 
working. 

 

 

• 

Remove the protective cover from the charging port on the scooter.  

• 

Ensure that the charging port is dry and not damaged before inserting the charger into 
the port. (Refer to the scooter diagram for location).   

• 

When the indicator on the charger is red, the scooter is charging.   

• 

The indicator light on the charger will turn green when the battery is fully charged. 
This usually takes 5-6 hours.   

• 

Do not over charge as long-term battery life may be affected. Do not leave unattended 
while charging.  

• 

When charging has completed, remove the charger and ensure that the protective 
cover is placed securely over the charging port.   
 

HOW TO RIDE  

IMPORTANT:

 Ensure all locking devices are secure and the scooter is stable before riding. 

This scooter is a toy and should be used as such. Do not ride in public areas. Adult 
supervision is required at all times.  

1.

 

Place one foot firmly on the deck, keeping your other foot on the ground for balance. 
Press the power button for 3 seconds to turn on the scooter.   

2.

 

Hold the handle bars with both hands and gently push the scooter forward. When you 
have gained a steady speed, gently press the accelerator and place both feet on the 
deck.  

3.

 

Press the mode button to change the max speed of the scooter. See display overview 
for more information.  

4.

 

Gently pressing the electronic brake and the rear brake will slow the scooter to a stop.  

5.

 

If the scooter displays that the battery is low, please charge the scooter. Do not run the 
scooter on low battery. 

6.

 

Press the power button for 3 seconds to turn off the scooter.  

7.

 

When the scooter has stopped, remove your feet one by one.   

 
MAINTENANCE

 

 

The scooter requires routine cleaning and maintenance. 

 

 

• 

Before any work is carried out on the scooter, ensure that the charging cable is not 
connected and that the scooter is powered off.   

• 

To clean the scooter, wipe the exterior with a soft damp cloth, then dry immediately.   

• 

The exterior of the scooter is splash proof with an ingress rating of IPX4. The scooter is 
water resistant, but not waterproof, never submerge the scooter, and do not ride in 
heavily dusty areas. Care should be taken to avoid mud, large puddles, avoid adverse 
weather.  

• 

Do not allow water to get inside of the scooter. There is a high risk of the internal 
electronics becoming permanently damaged.   

• 

The tyres on the scooter must be regularly checked for damage. 

Summary of Contents for E-SC10













Reviews: