background image

 

 Cleaning and user maintenance must not be carried out by 

children without supervision.  

 When the hood is being maintained, cleaned or filters 

changed, make sure it is switched off at the mains supply. 

 The exterior of the hood should be cleaned with mild detergent 

on a warm damp sponge or cloth.  

 The air must not be discharged into a flue that is used for 

exhausting fumes from appliances burning gas or other fuels.  

 Regulations concerning the discharge of air have to be 

fulfilled.  

 The minimum distance between the supporting surface for the 

cooking vessels on the hob and the lowest part of the hood 
must be at least 65 cm.  

 When the cooker hood is used in conjunction with appliances 

supplied with energy other than electric, the negative pressure 
in the room must not exceed 0,04 mbar to prevent fumes 
being drawn back into the room by the cooker hood.

 

 

 Failure to install the hood in accordance with these 

instructions may result in electrical hazards. 

 
CAUTION

:   

Accessible parts may become hot when used with cooking 
appliances.  
Deep fat fryers must be continuously monitored during use: 
overheated oil can burst into flames 

 

 

 

Summary of Contents for eiQ70CURVBL





















Reviews: