ELECTRO FREEZE Soft Serve Model 30T-RMT
184952
3
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
1234567890123456
2.3 Electrical Requirements
10% of voltage indicated on the nameplate.
Also, on three-phase systems, voltage
between phases must be balanced within
2%. (More than a 6 volt difference between
any two voltage measurements at 208-230
volts indicates a possible imbalance.)
Request your local power company to
correct any voltage problem.
3. An easily accessible main power
disconnect must be provided for all poles of
the wiring to the freezer.
CAUTION
To prevent accidental
electrical shock, a
positive earth ground
is required.
2.4 Electrical Connections
3. Refer to the wiring diagram provided
for proper power connections.
4. Electrical connections are made in
the junction box located mid-level behind the
left side panel.
5. Use a flexible connection when
permissible.
6. For 3 phase freezers, beater shaft
rotation must be clockwise as viewed from
the front of the freezer.
3.
All
models require a minimum 6
inch (15 cm) clearance on both the side
panels or the rear panel for adequate
ventilation. Freezers designed with top air
discharge require at least 18 inches (45 cm)
above the top panel be free of obstructions.
Anything blocking ventilation of the freezer
(including cone dispensers) will reduce the
efficiency of the freezer.
4.
Water cooled
models will require a
1/2 inch MPT water inlet and water waste
connection. Both condensers are tied
together so that one water inlet and one
water waste is all that is required. The
connections are found on the bottom under
the compressor mounting area and are
clearly tagged “Water Inlet” and “Water
Waste.” A manual shut-off valve should be
installed in the water inlet line at the time of
installation. Maintain inlet water pressure
above 35 (241kPa) and below 140 psig (965
kPa) for proper operation.
5. Place the freezer in the final loca-
tion and level by adjusting the legs or
casters so that it is level side-to-side and
the front is approximately ¼ inch (6 mm)
lower than the rear to allow proper drainage
of the freezing cylinder.
2.2
Installation
(continued)
1. Always verify electrical specifica-
tions on the data plate of each freezer. Data
plate specifications will always supersede
the information in this manual.
2. Supply voltage must be
CAUTION
To prevent accidental
electrical shock, a
positive earth ground
is required.
1. Double freezers with two compres-
sors require one power supply for each side
of the freezer. Each side of the freezer
operates independently.
2. Check the data plate for fuse size,
wire ampacity and electrical specifications.
