background image

 

 

Page 2 of 2 

XX017 

THESE WARRANTIES DO NOT COVER: 

1.  Costs for labor for removal and reinstallation of an alleged defective product or product parts, 

transportation to Electro Industries, and any other materials necessary to perform the exchange, 
except as stated in this warranty.  Replacement material will be invoiced to the distributor in the usual 
manner and will be subject to adjustment upon verification of defect. 

2.  Any product that has been damaged as a result of being improperly serviced or operated, including, 

but not limited to, the following: operated with insufficient water or airflow, allowed to freeze, 
subjected to flood conditions, subjected to improper voltages or power supplies, operated with airflow 
or water conditions and/or fuels or additives which cause unusual deposits or corrosion in or on the 
product, chemical or galvanic erosion, improper maintenance or subject to any other abuse or 
negligence. 

3.  Any product that has been damaged as a result of natural disasters, including, but not limited to, the 

following: lightning, fire, earthquake, hurricanes, tornadoes or floods. 

4.  Any product that has been damaged as a result of shipment or handling by the freight carrier.  It is the 

receiver’s responsibility to claim and process freight damage with the carrier. 

5.  Any product that has been defaced, abused, or suffered unusual wear and tear as determined by 

Electro Industries or its authorized representative. 

6.  Workmanship of any installer of the product.  This warranty does not assume any liability of any 

nature for unsatisfactory performance caused by improper installation. 

7.  Transportation charges for any replacement part or component, service calls, normal maintenance; 

replacement of fuses, filters, refrigerant, etc. 

CONDITIONS AND LIMITATIONS: 

1.  If at the time of a request for service the original owner cannot provide an original sales receipt or a 

warranty card registration then the warranty period for the product will have deemed to begin thirty 
(30) days after the date of manufacture and 

NOT

 the date of installation. 

2.  The product must have been sold and installed by a licensed electrical contractor, a licensed 

plumbing contractor, or a licensed heating contractor. 

3.  The application and installation of the product must be in compliance with Electro Industries’ 

specifications as stated in the installation and instruction manual, and all state and federal codes and 
statutes.  If not, the warranty will be null and void. 

4.  The purchaser shall have maintained the product in accordance with the manual that accompanies 

the unit.  Annually, a qualified and licensed contractor must inspect the product to assure it is in 
proper working condition. 

5.  All related heating components must be maintained in good operating condition. 

6.  All lines must be checked to confirm that all condensation drains properly from the unit. 

7.  Replacement of a product or product part under this limited warranty does not extend the warranty 

term or period. 

8.  Replacement product parts are warranted to be free from defects in material and workmanship for 

ninety (90) days from the date of installation.  All exclusions, conditions, and limitations expressed in 
this warranty apply. 

9.  Before warranty claims will be honored, Electro Industries shall have the opportunity to directly, or 

through its authorized representative, examine and inspect the alleged defective product or product 
parts. Remedies under this warranty are limited to repairing or replacing alleged defective product or 
product parts.  The decision whether to repair or, in the alternative replace, products or product parts 
shall be made by Electro Industries or its authorized representative. 

 

 

THESE WARRANTIES DO NOT EXTEND TO ANYONE EXCEPT THE ORIGINAL PURCHASER AT RETAIL AND ONLY WHEN THE PRODUCT IS IN THE ORIGINAL 
INSTALLATION SITE.  THE REMEDIES SET FORTH HEREIN ARE EXCLUSIVE. 

ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED WITH 
RESPECT TO ALL PURCHASERS OR OWNERS.  ELECTRO INDUSTRIES, INC. IS NOT BOUND BY PROMISES MADE BY OTHERS BEYOND THE TERMS OF THESE 
WARRANTIES.  FAILURE TO RETURN THE WARRANTY CARD SHALL HAVE NO EFFECT ON THE DISCLAIMER OF THESE IMPLIED WARRANTIES. 

ALL EXPRESS WARRANTIES SHALL BE LIMITED TO THE DURATION OF THIS EXPRESS LIMITED WARRANTIES SET FORTH HEREIN AND EXCLUDE ANY 
LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES RESULTING FROM THE BREACH THEREOF.  SOME STATES DO NOT ALLOW THE EXCLUSION OR 
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY.  PRODUCTS OR PARTS OF 
OTHER MANUFACTURERS ATTACHED ARE SPECIFICALLY EXCLUDED FROM THE WARRANTY. 

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS WHICH VARY UNDER THE LAWS OF EACH STATE. IF ANY 
PROVISION OF THIS WARRANTY IS PROHIBITED OR INVALID UNDER APPLICABLE STATE LAW, THAT PROVISION SHALL BE INEFFECTIVE TO THE EXTENT OF 
THE PROHIBITION OR INVALIDITY WITHOUT INVALIDATING THE REMAINDER OF THE AFFECTED PROVISION OR THE OTHER PROVISIONS OF THIS WARRANTY.

 

Summary of Contents for ELECTRO DUCT












Reviews: