S E T U P M E N U O P T I O N S
54
7.
Output Resolution
: To choose the output resolution that best matches your television’s native
resolution. For a detailed description on how to choose a proper output resolution, please refer
to the
Select the Best Output Resolution
section on page 23 of this manual.
8.
1080p24 Output
: To set 1080p 24Hz output options. This option only applies to the HDMI
output at 1080p resolution. Many Blu-ray Discs that originated from theatrical movies are
encoded using 24Hz frame rate, the same number of frames per second as the original
theatrical film. If the TV properly supports 1080p 24Hz, smoother motion can be achieved by
enabling
1080p24 Output
for such discs. The available options are:
•
Auto (default)
– Video encoded in 24Hz frame rate will be output as 1080p 24Hz if the TV
informs the player that it can support the 1080p24 signal.
•
On
– Video encoded in 24Hz frame rate will be output as 1080p 24Hz without regard to
whether the TV can support the 1080p24 signal or not. This is useful if the TV can actually
support 1080p24 but does not properly state its capability. Please note that if the TV cannot
support 1080p24, selecting this option will result in no video.
•
Off
– Video encoded in 24Hz frame rate will be converted to 60Hz (NTSC) or 50Hz (PAL)
9.
HDMI Options
: To configure video options that apply only to the HDMI output. This item
contains a sub-menu with multiple configuration options. Please refer to the
section on page 58 of this manual for details of each option.
10.
Display Options:
To configure the options for displaying on-screen information. The following
display options are available:
•
Subtitle Shift
– To set the display position for subtitles. When the “Subtitle Shift” is set at 0
(default), subtitles are displayed at the original position as specified on the disc. When it is
set at a value between 1 and 5, subtitles are shifted up. When it is set at a value between
-1 and -5, subtitles are shifted down. This feature is helpful for customers using a 2.35:1
“Constant Image Height” video projection system. Subtitles can be shifted to the active
video area so they do not get cut off.
•
OSD Position
– To set the display position for the on-screen display (OSD). When the
“OSD Position” is set at 0, the OSD is shown at the top and bottom of the video screen.
When it is set at a value between 1 and 5, the OSD is shifted towards the center of the
video screen. Similar to the subtitle shift setting above, the “OSD Position” feature is helpful
for customers using a 2.35:1 “Constant Image Height” video projection system.
•
OSD Mode
– To select how long the on-screen display information, such as elapsed or
remaining time, stays on the TV screen. The available options are:
•
Normal
– On-screen display information stays on the TV screen until the user cancels
it.
•
Silent
– On-screen display information shows on the TV screen for a few seconds and
then disappears. The front panel display still maintains the selected display
information.
•
Remaining
– On-screen display information stays on the TV screen until the user
cancels it. By default displays remaining time instead of elapsed time.
•
Angle Mark (on/off)
– To turn on/off the display of an angle mark when a DVD or Blu-ray
Disc with multiple available angles is played. Keeping the angle mark off avoids distraction
from normal movie watching.
•
PIP Mark (on/off)
– To turn on/off the display of a Picture-in-Picture mark when a Blu-ray
Disc with secondary video is played. Keeping the PIP mark off avoids distraction from
normal movie watching.
Summary of Contents for EMP 2
Page 1: ...EMP 2 High Performance Balanced Multiformat Player Owner s Manual ...
Page 2: ......
Page 6: ......
