RADIO OPERATION
1.
Set the Function Selector to the RADIO position.
2.
Slide the Band Switch to the "AM" or "FM" position.
3.
Turn the Tuning Knob to your desired radio station.
4.
Adjust the sound level by rotating the Volume Control Knob.
ANTENNA
For best reception, fully extend the FM Antenna to receive FM stations. For AM reception, the
unit has a built-in antenna, turn the whole unit for the best reception.
CD FUNCTION
To play a CD, please follow these steps.
1.
Set the Function Selector to the CD position.
2.
Lift open the CD door and insert the CD with the printed side facing up.
3.
Gently push close the CD door.
4.
Disc information: The total number of tracks will appear on the LED display.
5.
Press the Play/Pause button to start playing the CD.
6.
Adjust the volume control to the desired volume level.
7.
Press the Stop button, to stop playing the CD.
Skip Mode
1.
During play or pause mode, if the Skip
button is pressed, it will go to the next track and
display the track number on the LED Display. If in play mode, the next track will begin to
play. If in pause mode, it will remain paused.
2.
During play or pause mode, if the Skip
button is pressed once, it will go back to the
beginning of the track and display the number on the LED Display. If in play mode, the next
track will begin to play. If in pause mode, it will remain paused.
3.
During play or pause mode, if the Skip
button is pressed twice, it will go to the previous
track and display the number on the LED Display. it will If in play mode, the next track will
begin to play. If in pause mode, it will remain paused.
Programming the CD Player
To program the CD Player, please ensure the CD is in
STOP
mode.
1. Press the PROGRAM button to begin programming the CD player.
2. Press the Skip
or Skip
buttons, to select your desired track.
3. Once the number of the desired track appears on the display, press the PROGRAM button
again to store the track in the memory.
4. Repeat steps 2 to 3 to store more tracks in the memory. You can store a maximum of 20
tracks.
5. Press the PLAY/PAUSE button to play the disc in the programmed order.
6. To stop playing, press the STOP button.
7. To cancel the programmed tracks, press the STOP button or select a different function
mode (AUX/OFF or RADIO).
Repeat Mode
Repeat 1:
When the Repeat button is pressed once, the Repeat LED Indicator will light and flash
continuously. This single track will be repeated.
Repeat All:
When the Repeat button is pressed twice, the Repeat LED Indicator will stay lighted.
The whole disc will be played repeatedly.
To Cancel Repeat Function:
Press the Repeat button until the lighted Repeat LED Indicator
turns
- EN 3 –
MP3/AUX IN CONNECTION
1.
Insert an audio cable (requires 3.5mm stereo plug, not supplied) into the Line Out Jack or
Head Phone Jack on your MP3 Player and insert the other end into the corresponding AUX
Input Jack on this product.
2.
Slide the Function Selector to the AUX/OFF position.
3.
Make sure your device is turned on and if applicable, set to the AUX setting. (Follow your
devices instruction manual for further guidance).
4.
To stop this function, simply turn off the attached device, or select a different function mode
(CD or RADIO).
CARE AND MAINTENANCE
Precautions
1.
Always turn off the unit after use.
2.
Keep the unit away from magnetic objects, water or heat sources.
3.
Use a clean soft cloth moistened with lukewarm water to clean the cabinet. Never use
chemical cleaners that could damage the finish of the unit.
4.
Never touch the CD tray or the lens. If fingerprints are on the lens or tray, clean it gently
with a commercial lens cleaner.
5.
Disconnect the unit from any power sources before cleaning.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
Contact 1-800-663-5954 for any technical support or servicing.
NOTE:
When playing audio soundtracks with high pitch or octave sounds, the speakers on the
unit may cut out the sound. This is normal, and is not a malfunction of the unit. To solve this
problem, simple change tracks.
SPECIFICATIONS
Frequency Range:
AM 530 - 1710 KHz
FM 88 - 108 MHz
Power Supply:
AC 120V ~ 60Hz
DC 9V
(6 “C” size batteries, not included)
Specifications are subject to change without notice.
- EN 4 -
