g
26
Inserting tools
The following tools can be selected for
insertion:
• Whisking disk (fig. 1/R) or
• Metal blade (fig. 1/Q) or
• Plastic blade (fig. 1/P) or
• Insert holder (fig. 1/O) with cutting
insert (fig. 9)
3
The insert holder must be fitted with
the appropriate insert depending on
the purpose of application (see "Insert-
ing cutting insert in insert holder").
0
Place desired tool on spindle.
– Whisking disk, metal blade and plas-
tic blade (fig. 8) mesh with the teeth
underneath on the spindle.
– The insert holder (fig. 11) rests on
the hexagonal spindle.
3
Preferably hold the insert holder with
two fingers in the two handle holes.
Fitting the cover (fig. 6)
0
Place cover (fig. 1/F) on the all-purpose
bowl (arrow
on arrow
) and
turn
counter-clockwise
to the stop.
The cover can be heard to engage. The
nose of the cover is then directly above
the handle, both black arrows must
coincide.
0
Insert stopper (fig. 1/E) in filling inlet.
Inserting cutting insert in insert
holder (fig. 10)
The appropriate insert must be placed
in the insert holder depending on use.
3
The inserts are contained in the hinged
accessories compartment (fig. 1/K) in
the motor casing.
1
The inserts are very sharp. They should
be held only with the handle!
0
Open accessories compartment by
pulling the handle (fig. 9).
0
Take required insert by the handle from
the accessories compartment (fig. 9).
0
Place the insert with the tip at the cen-
tre of the insert holder and place in the
recess of the disk (fig. 10).
0
To remove the insert draw slightly out-
wards with the handle and raise.
Operating multifunction section
0
Open cover (fig. 1/F) and place all
ingredients required in the all-purpose
bowl.
Caution:
Do not exceed maximum fill-
ing volume:
– liquid 1.75 litres
– solid 1.5 litres
3
Further ingredients can be added dur-
ing operation through the filling inlet.
The filling beaker in the stopper (fig.
1/E) can also be used for this purpose.
Close the filling inlet immediately each
time to avoid splashes.
1
Use the stopper exclusively to com-
press the cutting items!
0
Start the appliance: turn speed selector
(fig. 1/l) right to the desired speed set-
ting or press the pulse button (fig. 1/J).
3
It is recommended to start at a slow
speed and then to increase the speed.
The appliance operates at maximum
speed by pressing the pulse button.
Refer to the section "Tips on using
multifunction section" for reference
values.
1
If the warning lamp (fig. 4/a) flashes
and the appliance cannot be started,
the safety cover for the mixer drive
(figs. 1/T and 4) is not properly fitted.
0
Switch off appliance: turn speed selec-
tor left to the "0" position.
0
After using, turn cover
clockwise
and
remove.
1
Only remove the cover when the tool
has come to a complete stop!
0
Remove the tool and spindle.
0
Turn the all-purpose bowl
clockwise
and remove.
822_949_289 KM850_880.book Seite 26 Mittwoch, 23. Januar 2008 9:07 21
Summary of Contents for AEG KM 8 Assistent Series
Page 3: ...3 a 3 2 5 4 7 6 822_949_289 KM850_880 book Seite 3 Mittwoch 23 Januar 2008 9 07 21 ...
Page 4: ...4 11 10 9 8 822_949_289 KM850_880 book Seite 4 Mittwoch 23 Januar 2008 9 07 21 ...
Page 5: ...5 a b b a c 12 13 14 15 822_949_289 KM850_880 book Seite 5 Mittwoch 23 Januar 2008 9 07 21 ...
Page 103: ...103 822_949_289 KM850_880 book Seite 103 Mittwoch 23 Januar 2008 9 07 21 ...
