g
27
Citrus press
Preparation (fig. 13)
0
Fit all-purpose bowl as described above
(fig. 5).
0
Place sieve insert of citrus press (fig.
13/a) on all-purpose bowl (arrow
on arrow
) and turn
cunter-clock-
wise
to the stop. The sieve insert can
be heard to engage, arrow
must
coincide with arrow
.
0
Insert press cone (fig. 13/b) in sieve
insert.
Operating citrus press
0
Start appliance: turn speed selector
(fig. 1/I) right to position 1.
3
The citrus press must only be operated
at the lowest speed.
0
Switch off appliance: turn speed selec-
tor left to the "0" position.
0
Remove press cone after use.
0
Turn sieve insert
clockwise
and remove.
0
Turn all-purpose bowl
clockwise
and
remove.
1
The appliance can be used for up to
10 minutes without stopping. It should
be allowed to cool each time following
prolonged, continuous operation (for
at least 20 minutes after using for
10 minutes without stopping).
Cleaning and care
Motor casing
1
Ensure that no liquid enters the motor
casing!
0
Clean the motor casing with a moist
cloth.
Never immerse in water or hold
under running water!
Mixer
3
Container and blade can be cleaned
easily and properly with the aid of the
pulse position.
0
Fill the mix container half full with
warm (not hot!) water and add a few
drops of detergent.
0
Press the pulse button briefly.
0
Then rinse the container under running
water.
Dismantle/fit blade unit (fig. 14)
3
If necessary, the blade unit can also be
dismantled and cleaned separately.
1
Caution: The blade is very sharp!
Danger of injury!
0
Release blade unit (fig. 14/a) from mix
container using the closing cover
(fig. 1/D and fig. 14/c) as tool. The
grooves of the closing cover fit the ribs
of the blade unit. Turn
counter-clock-
wise
and remove while holding slightly
at an angle.
0
Remove gasket (fig. 14/b) from blade
unit.
1
The blade unit is very sharp. The gasket
can be damaged.
1
Rinse the components carefully by
hand (
danger of injury!
). Use only
water and detergent for cleaning.
Do not clean the blade unit in a dish-
washer.
0
Insert gasket in blade unit.
0
Insert blade unit in container from
below. Hold blade unit at a slight angle.
Tighten blade unit using the closing
cover as tool by turning
clockwise
(fig. 14).
All-purpose bowl and tools
0
The all-purpose bowl and tools should
be cleaned in rinsing water.
1
Caution: The metal blade is extremely
sharp! Danger of injury!
822_949_289 KM850_880.book Seite 27 Mittwoch, 23. Januar 2008 9:07 21
Summary of Contents for AEG KM 8 Assistent Series
Page 3: ...3 a 3 2 5 4 7 6 822_949_289 KM850_880 book Seite 3 Mittwoch 23 Januar 2008 9 07 21 ...
Page 4: ...4 11 10 9 8 822_949_289 KM850_880 book Seite 4 Mittwoch 23 Januar 2008 9 07 21 ...
Page 5: ...5 a b b a c 12 13 14 15 822_949_289 KM850_880 book Seite 5 Mittwoch 23 Januar 2008 9 07 21 ...
Page 103: ...103 822_949_289 KM850_880 book Seite 103 Mittwoch 23 Januar 2008 9 07 21 ...