background image

28

Changing The Filter

To replace your 

pure advantage

TM 

water filter:

It is not necessary to turn the water supply off to change the filter. Be ready to wipe
up any small amounts of water released during the filter replacement. The bottom
of the filter housing includes two small water drainage holes, so be sure to remove
any stored food from the top shelf.

1

Turn 

Off

 the ice maker power switch (see page 23 for

more about turning off the ice maker).

2

Push the filter release button to the right of the
cartridge to disconnect it.

3

Slide the old filter cartridge straight out of the housing
and discard it.

4

Unpackage the new filter cartridge and slide it gently
into the filter housing until it stops against the snap-in
connector at the back of the housing.

5 Push firmly until the cartridge snaps into place

.

When fully engaged, the front of the filter cartridge
should be flush with the filter release button.

6

Turn 

On

 the ice maker power switch (see page 23 for

more about turning on the ice maker).

7

Press a drinking glass against the water dispenser
while checking for any leaks at the filter housing. Any
spurts and sputters that occur as the system purges air
out of the dispenser system are normal.

8

After filling one glass of water, continue flushing the
system for about three minutes.

9

Press and hold the 

Filter Status

 button on the Ice &

Water Dispenser control panel for 3 seconds. The light
flashes red, amber, and green to indicate the 

Filter

Status

 has been reset.

NO

NO

NO

NO

NOTE

TE

TE

TE

TE

The o-rings on a new water filter are lubricated. To ensure a good
seal, please do not remove this lubricant.

Summary of Contents for E23CS78DSS









































Reviews: