background image

1

ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS

A

B

D

I

28

3

/

32

"

(71.4 cm)

C

H

F

G

2" (5.1 cm)

Min.

1

1

/

2

"

(3.8 cm)

Min.

31"*

(78.7 cm)

3" (7.6 cm)

Max.

Spacer

** Door Open

(see note)

Electrical

Junction Box

4" X 4" (10.2 cm x

10.2 cm) opening to

route armoured

cable.

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

FOR YOUR SAFETY:  Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.

The first step of your installation should be to measure your current cutout dimensions and compare them
to the cutout dimensions chart below. You may find little or no cabinet work will be necessary.

NOTE:

1. Base must be capable of supporting 200 pounds (90.7 kg).
2. Make sure base is level and front of cabinet is square. If the cabinet

base is not level, the oven glides will tend to slide out
when opening the door.

Figure 1

P/N 318201519 (0411) Rev. A

All dimensions are in inches (cm).

 Do not remove spacers on the side walls and/or on the back of the built-in oven. These spacers

center the oven in the space provided. The oven must be centered to prevent excess heat buildup that may result
in heat damage or fire.

PRODUCT DIMENSIONS

CUTOUT DIMENSIONS AND CABINET WIDTH

MODEL

30" (76.2 cm) Wall Oven

MODEL

30" (76.2 cm) Wall Oven

A

30 (76.2)

Min.    F   Max.

28

½

 (72.4)      29 (73.7)

B

29

½

 (74.9)

G (Min.)

24 (61)

C (Rear wrapper)

28 (71.1)

Min.    H   Max

.

28

1

/

4

 (71.8)   28

7

/

8

 (73.3)

D

24

1

/

8

 (61.3)

I

30 (76.2) Min

** NOTE:

 Allow at least 23¼" (59.1 cm)

clearance for door depth when it is open.

NOTE:

 Dimension

 G

 is critical to the

proper installation of the built-in oven.  If
the oven decorative moulding does not
butt against the cabinet, or if noise is
heard on convection models, verify
dimension 

G

 to assure it is according to

the required dimension.

* Suggested distance from floor is 31" (78.7 cm).

Minimum required distance is 4½" (11.4 cm).

NOTE:

 For combination of this Built-in Oven with Warm &

Serve Drawer model no 

E30WD75DSS

 see cutout dimensions

specified in the Warm & Serve Drawer Installation Instructions.

Printed in the USA

Summary of Contents for E30EW75EPS - Icon Professional Series









Reviews: