background image

 

Electrolux 

EFS – Dishwashing Systems Platform 

Electrolux Professional 

 

Electronic Dishwasher 

SERVICE MANUAL

 

 

 

DOC. NO. 5956.446.06 

 

©Copyright 2005 by

 

Electrolux Professional

 

P.62/88 

 

 

WT30C (Café Line) 

Prog. 038 

1. 

Switch OFF and then switch ON the machine. 

2. 

CFG

 

Enter into CFG parameter family and set the following parameters. 

 

 

tYP    0 

Hood Type like working cycles. 

 

 

boi    0 

Atmospheric boiler. 

 

 

doo    2 

Front loading door type. 

 

 

dFL    3 

Default values for Undercounter models. 

 

 

trc    1 

SOFT START ENABLED. 

 

 

b_t    1 

Tank heater works only if boiler temperature reached. 

 

 

btF   75 

Enable filling tank by means of rinsing cycles. 

 

 

LES    1 

Detergent level switches enabled. 

 

 

UI 

  9 

Select user interface hood type model 

(up to version 3.11 set to 

1

)

.

 

 

 

RE 

  0 

Regeneration cycle disabled. 

 

 

ALr    1 

ALARMS ENABLED. 

3. 

Switch OFF and then switch ON the machine. 

4.  Modify Factory parameters: 
 

FAC 

Enter into FAC parameter family. 

 

 

bt°C   84 

Boiler Temperature Threshold. 

 

 

bAJ    0 

Boiler Temperature Adjust. 

 

 

btd    3 

During stand-by boiler is kept at lower temperature than Temperature Threshold. 

 

 

tt°C   68 

Tank Temperature Threshold. 

 

 

ttH    2 

HISTERESIS of  Tank Temperature. 

5. 

Modify the cycle parameters: 

 

CY1

 

Cycle 1 parameters family. 

 

 

Ln1

 

  1

 

Long Wash Phase [min] 

 

 

Sh1   36 

Short Wash Phase [s] 

 

 

FP1    4 

Final Pause [s] 

 

CY2

 

Cycle 2 parameters family. 

 

 

Ln2

 

  2

 

Long Wash Phase [min] 

 

 

Sh2   36 

Short Wash Phase [s] 

 

 

FP2    4 

Final Pause [s] 

 

CY3

 

Cycle 3 parameters family. 

 

 

Ln3

 

  3

 

Long Wash Phase [min] 

 

 

Sh3   36 

Short Wash Phase [s] 

 

 

FP3    4 

Final Pause [s] 

 

dPA

 

Set other parameters. 

 

 

C F

 

  1

 

Fahrenheit. 

6. 

Switch OFF and then switch ON the machine. 

 

Summary of Contents for EDW7505HPS - Semi-Integrated Dishwasher With 5 Wash Cycles

























































































Reviews: