background image

3

Hob Burners Control Knobs

The hob burners control knobs are situated on the hob

front panel. The symbols on the knobs mean that :

there is no gas supply

 

there is maximum gas supply

  

there is minimum gas supply

Lighting the Burners

• For easier lighting, proceed before putting a pan

on the pan support.

Push in the relevant knob and turn it anticlockwise

to "maximum position". After lighting the flame,

keep the knob pushed down for about 5 seconds.

This will allow the "thermocouple" (Fig. 1 - lett. D)

to be heated and the safety device to be switched

off, otherwise the gas supply would be interrupted.

Then, check the flame is regular and adjust it as

required.

If you cannot light the flame even after several

attempts, check the "cap" and "crown" (Fig. 1 -

lett. A-B) is in the correct position.

To put the flame out, turn the knob to the symbol

"

l

".

• Always turn the flame down or put it out before

taking the pans off the burner.

Burner

minimum

maximum

diameter

diameter

Triple Crown

180 mm.

260 mm.

Big (rapid)

180 mm.

260 mm.

Medium (semirapid)

120 mm.

220 mm.

Small (auxiliary)

80 mm.

160 mm.

Fig. 1

FO 0204

Using the hob correctly

To  ensure  maximum  burner  efficiency,  it  is  strongly

recommended that you use only pots and pans with a

bottom fitting the size of the burner used, so that flame

will not spread beyond the bottom of the vessel (see the

table beside).

It is also advisable, as soon as a liquid starts boiling, to

turn down the flame so that it will barely keep the liquid

simmering.

Use only pans or pots with flat bottom.

Carefully  supervise  cookings  with 

fats  or  oil

,

since these types of foodstuff can result in a fire,

if over-heated.

Contents

Instruction for the User

l

Important Safety Information

2

Instruction for the User

3

Maintenance and Cleaning

4

Service and original spare parts

5

Technical Data

5

Instruction for the Installer

6

Electrical connection

7

Adaptation to different types of gas

8

Building In

9

Possibilities for insertion

10

For the User

For the Installer

This appliance complies with the following

E.E.C. Directives:

- 73/23

 - 

90/683

 (Low Voltage Directive);

- 89/336

 (Electromagnetical Compatibility Directive);

-

90/396

 (Gas Appliances)

- 93/68

 (General Directives)

and subsequent modifications.

MANUFACTURER:

ELECTROLUX HOME PRODUCTS ITALY S.p.A.

Viale Bologna 298 - 47100 FORLI’ (Italy)

F

Summary of Contents for EHG 7730











Reviews: