background image

Problem

Possible solution

The program does not start.

Make sure that the appliance door is closed.

 

Press 

Start

.

 

If the delay start is set, cancel the setting or
wait for the end of the countdown.

The appliance does not fill with
water.

Make sure that the water tap is open.

 

Make sure that the pressure of the water sup-
ply is not too low. For this information, con-
tact your local water authority.

 

Make sure that the water tap is not clogged.

 

Make sure that the filter in the inlet hose is not
clogged.

 

Make sure that the inlet hose has no kinks or
bends.

The appliance does not drain the
water.

Make sure that the sink spigot is not clogged.

 

Make sure that the drain hose has no kinks or
bends.

The anti-flood device is on.

Close the water tap and contact the Service.

After the checks are completed, deacti-
vate and activate the appliance. The pro-
gram continues from the point of interrup-
tion.
If the problem occurs again, contact the
Service.
If the display shows other alarm codes,
contact the Service.

10.1 

If the washing and drying

results are not satisfactory

Whitish streaks or bluish layers on
glasses and dishes

• The released quantity of rinse aid is too

much. Adjust the rinse aid selector to a
lower position.

• The quantity of detergent is too much.

Stains and dry water drops on
glasses and dishes

• The released quantity of rinse aid is not

sufficient. Adjust the rinse aid selector
to a higher position.

• The quality of the detergent can be the

cause.

Dishes are wet

• The program is without a drying phase

or with a low temperature drying phase.
Leave the door ajar for some minutes
before you remove the dishes.

• The rinse aid dispenser is empty.
• The quality of the rinse aid can be the

cause.

• The quality of the multi-tablets can be

the cause. Try a different brand or acti-
vate the rinse aid dispenser and use
rinse aid together with multi-tablets.

Refer to “HINTS AND TIPS” for
other possible causes.

10.2 

How to activate the rinse

aid dispenser

1.

Press the on/off button to activate the
appliance. Make sure that the appli-
ance is in setting mode, refer to “Set-
ting and starting a program”.

2.

Press and hold, at the same time, 

De-

lay

 and 

EnergySaver

 until the indica-

tors 

 , 

 and 

start to flash.

3.

Press 

TimeSaver

,

ENGLISH

17

Summary of Contents for ESF 6700ROW

























Reviews: