background image

8

Setting electronically:

1.

Press the ON/OFF button.

3

If the LED indicator of only one programme
button is illuminated, this wash programme
has been activated. The wash programme
must be deselected:
Press function buttons 

2

and

simultaneously

for approx. 2 seconds. 
The LED indicators of all the programme but-
tons that can be selected will illuminate.

2.

Press function buttons 

2

and

3

 simultaneously and

hold them down.
The LED indicators for function buttons 1 to 3 will
flash.

3.

Press function button 

1

.

The LED indicator for function button 

1

 will flash.

The LED indicator for the end of the dishwashing
cycle will flash simultaneously:

The number of times that the LED indicator for the
end of the dishwashing cycle flashes corresponds
to the hardness setting. 

This sequence of flashes is repeated several times,
with a 3 second pause in-between.

4.

Pressing function button 

1

 increases the hard-

ness setting by 1 degree.
(Exception: hardness setting 1 follows hardness
setting 10).

5.

When the hardness setting is correct, press the
ON/OFF button.
The hardness setting is now saved. 

If the water softener is set electronically to “1”, this
switches off the control indicator for dishwasher salt.

 

Water hardness

Setting for

water hardness

Number of

flashes

Number of

acoustic 
signals

1)

in

°d

2)

in

mmol/l

3)

Range

Manual

Electronic

51

 - 

70

43

 - 

50

37

 - 

42

29

 - 

36

23

 - 

28

9.0

 - 

12.5

7.6

 - 

8.9

6.5

 - 

7.5

5.1

 - 

6.4

4.0

 - 

5.0

IV

1

10 

4)

9
8
7
6

10

9
8
7
6

10

9
8
7
6

0*

19

 - 

22

15

 - 

18

3.3

 - 

3.9

2.6

 - 

3.2

III

5

4*

5
4

5
4

11

 - 

14

1.9

 - 

2.5

II

3

3

3

4

 - 

10

0.7

 - 

1.8

I/II

2

2

2

below 4

below 0.7

I

1

no salt required

1

1

1) The water hardness will only be indicated acoustically if the acoustic signal has been activated.
2) (°d) German degree, measure of the hardness of water
3) [mmol/l] millimol per litre, international unit for water hardness
4) On this setting the length of the dishwashing cycle may be slightly longer.
*) factory setting

Summary of Contents for ESL 6226









































Reviews: