Electrolux EW30IS8CRS, Installation Instructions Manual

7

30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

Four Conductor Wire Connection to Range

Where local codes DO NOT permit connection of the 

frame grounding conductor to the neutral wire of the 

copper power supply cord (see Figure 4):

1.  Remove the screw holding the rear wire cover, 

then remove the rear wire cover (access cover) 

to expose range terminal connection block (see 

Figure 2).

2.  Remove the grounding strap. Remove the screw 

that holds the strap against the appliance. Cut the 

strap off at the terminal block, or bend the strap 

back and forth to break it from the terminal block. 

5.

 Electrical Connection to the 

Range (U.S.A.)

Three Conductor Wire Connection to 

Range

If local codes permit connection of the frame grounding 

conductor to the neutral wire of the copper power 

supply cord (see Figure 3):

1.  Remove the screw holding the rear wire cover, 

then remove the rear wire cover (access cover) 

to expose range terminal connection block (see 

Figure 2).

2.  Using the nuts supplied in the literature package, 

connect the neutral of the copper power supply 

cord to the center silver-colored terminal of the 

terminal block, and connect the other wires to the 

outer terminals. Match wires and terminals by color 

(red wires connected to the right terminal, black 

wires connected to the left terminal) (see figure 3).

3.  Put back the rear wire cover using the screw 

removed on step 1.

Figure 3

Silver Colored Terminal

1 1/8" (2,9 cm) Dia. 

Direct Connection 

Hole. Punch Out 

Knockout for 1 3/8" 

(3,5 cm) Dia. Cord 

Kit Hole.

To 240 V 

Receptacle

A User Supplied 

Strain-relief Must 

Be Installed at This 

Location.

Black 

Wire

Terminal

Block

Cord 

Mounting 

Plate

Neutral 

(White Wire)

Grounding

Strap

Red Wire

DO NOT loosen the screws that attach the terminal 

block to the appliance.

3.  Using the nuts supplied with the literature package, 

connect the ground wire (green) of the copper 

power supply cord to the frame of the appliance with 

the ground screw, using the hole in the frame where 

the ground strap was removed (see Figure 4).

4.  Connect the neutral of the copper power supply 

cord to the center silver-colored terminal of the 

terminal block, and connect the other wires to the 

outer terminals. Match wires and terminals by color 

(red wires connected to the right terminal, black 

wires connected to the left terminal).

5.  Put back the rear wire cover using the screw 

removed on step 1.

Direct Electrical Connection to the Circuit 

Breaker, Fuse Box or Junction Box

 Disconnect power to the circuit breaker 

or fuse box before making the electrical connection.
If the appliance is connected directly to the circuit 

breaker, fuse box or junction box, use flexible, armored 

or nonmetallic sheathed copper cable (with grounding 

wire). Supply a U.L. listed strain-relief at each end of 

the cable. At the appliance end, the cable goes through 

the Direct Connection Hole (see Figure 4) on the Cord 

Mounting Plate. Wire sizes 

(copper wire only)

 and 

connections must conform to the rating of the appliance.

Where local codes permit connecting the 

appliance-grounding conductor to the neutral 

(white) wire (see Figure 5):

Terminal Block

Silver Colored Terminal 

Red

Wire

Neutral 

(White Wire)

Ground (Bare 

Copper Wire)

To 240 V 

Receptacle

A User Supplied 

Strain-relief Must 

Be Installed at 

This Location

Black Wire

1 1/8" (2,9 

cm) Dia. 

Direct 

Connection 

Hole. Punch 

Out Knockout 

for 1 3/8" (3,5 

cm) Dia. Cord 

Kit Hole.

Figure 4