22 www.electrolux.com
Measure out the amount of
detergent required, pour it into the
main wash compartment .
Do not use gelatinous or thick
liquid detergents.
Do not put more liquid than the
maximum level.
Do not set the “Delay Start”.
Do not set the “Prewash” phase.
When you use the liquid
detergent
Pull out the dispenser drawer until
it stops.
−
−
−
−
−
−
Measure out the detergent and the
fabric softener;
2.
If you wish to carry out the
“Prewash” phase, pour it into the
compartment marked .
If required, pour fabric softener into
the compartment marked .
−
Close the drawer gently.
−
−
Residues of detergent, softener and
water may remain in the dispenser.
It is recommended to clean the
dispenser regularly to remove any
residue.
The softener amount used must not
exceed the “MAX” mark in the
drawer.
If you use thick softeners it is
recommended to dilute with water.
If you want your laundry to be spun or
use temperature different from the one
proposed by the Washer-Dryer, press
“Spin” and “Temp” touchpads
repeatedly to change the spin speed
and temperature.
Press the option touchpads, if you
want your laundry to be washed with
special functions.
Different functions can be combined
which is dependent on the program
selected.
If an option is not compatible with
the program selected, the symbol
“ ” will flash on display along
with buzzer sound.
If you want to delay the start of the
program, press the “Delay Start”
touchpad repeatedly to choose your
Washer-Dryer delay time.
−
−
1.
2.
NOTE
NOTE
NOTE
5.3 Options Setting
23
The appliance will automatically adjust
the selected program duration
according to the type and size of the
load.
−
The display will show adjusted
program duration.
−
To start a program, press the Start/Pause
touchpad. The corresponding pilot light
will stop flashing and a default program
duration will be displayed on the screen.
After approx. 15 minutes from the start of
a program:
If you press any touchpad while a
program is operating, the symbol “ ”
will flash on display along with buzzer
sound. (except Start/Pause touchpad and
On/Off button)
To pause, press Start/ Pause.
The indicator will start flashing.
−
Press the Start/Pause again.
The program will continue.
−
Changing a running program
is possible
only by switching off
the appliance.
Press the “On/Off” button to cancel
the program and to turn off the
appliance.
−
It may be possible to change some of the
options after a program has started.
Press the “On/Off” button again to
start the appliance.
−
Press the touchpad Start/Pause. The
indicator will start flashing.
1.
If available change the options that
you wish.
2.
Press Start/Pause again. The program
will continue.
3.
While a program or the Delay Start is
operating, the appliance door is locked
and the display shows the indicator “ ”.
First, set the machine to PAUSE by
pressing the “Start/Pause” touchpad. Wait
until the door lock indicator goes off, then
the door can be opened.
If the door lock indicator “ ” does not
disappear, this means that the machine
is already heating and the water level is
above the bottom edge of the door or the
drum is turning. In this case the door
CAN NOT be opened. If you need to
open it, you must drain the water to open
the door.
NOTE
NOTE
Now you can set a new wash program
and change any available options. Press
Start/Pause to start the new program.
The appliance will not drain the water
(except programs; Vapour Refresh, Spin,
Rinse + Spin).
In case of Remote ( ) function is
activated, when program cycle end and
anticrease phase is complete. The door
will remain locked for 5 minutes, if you
want to open the door at that time, press
Remote ( ) touchpad once to turned off
function then the door is unlocked.
5.4 Starting A Cycle ( )
5.7 Changing The Options
5.8 Opening The Door
5.5 Interruption Of A Program
5.6 Changing A Program
In case of emergency please refer
to “Emergency door opening” on
page 40.
Summary of Contents for EWW1142ADWA
Page 92: ...G0030937 001 A21791305 ...