66 www.electrolux.com
如果希望使用不同於洗衣機建議的脫
水速度和溫度洗滌衣物,請反覆按脫
水「
Spin
」和溫度「
Temp
」觸控
按鈕,更改脫水速度和溫度。
如果希望使用特殊功能洗滌衣物,
根據需要按相應選項的觸控按鈕。
根據選定的洗衣程序的不同,可以
組合使用各種不同功能。
如果選擇了與預設洗滌程序不相容
的選項,「 」訊息將閃爍,並
發出嗶嗶聲。
如果希望預約洗衣程序,按下預約
觸控按鈕「
Delay Start
」,選擇洗
衣機的預約時間。
-
-
1.
2.
請勿使用膠狀或粘稠的液體洗
滌劑。
-
投放的液體洗滌劑不得超過最
大液位線。
-
請勿設定預約功能。
-
請勿設定預洗階段。
-
使用液體洗滌劑時
在洗滌程序完成後,洗滌劑、
織物柔軟劑和水可能會沉積在
洗滌劑料盒裡。建議經常清洗
洗滌劑料盒,以清除沉積物。
用量不得超過抽屜盒的最大
標記「
MAX
」
建議使用濃縮織物柔軟劑時
先用水稀釋柔軟劑。
視需要量,取適量洗滌劑,倒入
主洗盛載格中 。
拉出洗滌劑放入盤,直到拉不動
為止。
-
-
量取適量的洗滌劑和衣物柔順劑;
如果要執行「預洗」階段,請將洗
滌劑倒入標有 的盛載格中。
如果需要,可將衣物柔順劑倒入
標有 的盛載格中。
-
-
5.3 選項設定
洗衣機將自動停止運作。
提示聲將響起。
顯示畫面將顯示「 」。
啟動/暫停觸控按鈕的標誌將熄滅。
-
-
-
-
-
-
-
-
門鎖標誌「 」將熄滅。
將衣物從洗衣機內取出。確保滾筒已
完全清空。
保持機門微開,以免滋生黴菌和產生
異味。
關閉水龍頭。
在洗滌程序結束時,洗滌剩餘時間可能突
然從 7 分鐘或更短時間縮短至 0 分鐘,這
是因為在自動感應衣服容量時所預估的總
洗滌時間過長。在某些情況下(負荷完美
平衡),在自動感應衣服容量之後,洗滌
時間可能會短於預估時間。這是機器的正
常運作,因此不必擔心,因為這不會影響
洗滌效果。
洗衣機將根據衣物類型和衣物量,自
動調整選定的程序持續時間。
-
顯示畫面將顯示調整後的程序持續時間。
-
要啟動程序,請按啟動/暫停( )觸
控按鈕,對應的指示燈將停止閃爍,顯
示畫面上將顯示預設的程序持續時間。
程序啟動約 15 分鐘後:
要暫停程序,請按啟動/暫停按鈕。
對應的標誌將開始閃爍。
-
再次按啟動/暫停觸控按鈕。程序將
繼續運作。
-
程序啟動後,只能更改部分選項。
按下啟動/暫停觸控按鈕。對應的標
誌將開始閃爍。
1.
更改選項。
2.
再次按啟動/暫停觸控按鈕。程序將
繼續運作。
3.
洗衣程序或預約功能運作時,機門將保
持緊鎖狀態,同時顯示畫面顯示「 」
標誌。首先按啟動/暫停觸控按鈕,將洗
衣機設為「
PAUSE
」(暫停)狀態。待
門鎖標誌熄滅後,即可將機門打開。
如果門鎖標誌「 」沒有消失,
表示洗衣機已經在加熱,並且水位高出
機門底邊,或者滾筒正在轉動。這種情
況下,機門將無法打開。如果您需要打
開它,你必須瀝乾水再開門。(請閱讀
「進行排水」章節)
注意!
如果在程序正在運作時按下任何觸控
鍵,顯示畫面將顯示「 」消息,
並發出嗶嗶聲。(啟動/暫停觸控鍵和
電源開/關按鈕除外)
要更改正在運作的程序,只能關閉洗衣
機電源。
按電源開/關按鈕取消程序並關閉洗
衣機。
-
再次按電源開/關按鈕啟動洗衣機。
在此期間,洗衣機不會排水
(除了程序;
Vapour Refresh
、
Spin
,
Rinse + Spin
)。
-
備註
此時即可設定新的洗衣程序。
當程序設計循環結束和防皺階段完成時
,在
Remote
( ) 功能的情況下啟動。
門會保持鎖定狀態 5 分鐘,如果你想在
那個時候開門,請按
Remote
( ) 觸控
板一次以關閉功能,則門會開鎖。
注意!
2
.
67
洗衣機將自動停止運作。
提示聲將響起。
顯示畫面將顯示「 」。
啟動/暫停觸控按鈕的標誌將熄滅。
-
-
-
-
-
-
-
-
門鎖標誌「 」將熄滅。
將衣物從洗衣機內取出。確保滾筒已
完全清空。
保持機門微開,以免滋生黴菌和產生
異味。
關閉水龍頭。
在洗滌程序結束時,洗滌剩餘時間可能突
然從 7 分鐘或更短時間縮短至 0 分鐘,這
是因為在自動感應衣服容量時所預估的總
洗滌時間過長。在某些情況下(負荷完美
平衡),在自動感應衣服容量之後,洗滌
時間可能會短於預估時間。這是機器的正
常運作,因此不必擔心,因為這不會影響
洗滌效果。
洗衣機將根據衣物類型和衣物量,自
動調整選定的程序持續時間。
-
顯示畫面將顯示調整後的程序持續時間。
-
要啟動程序,請按啟動/暫停( )觸
控按鈕,對應的指示燈將停止閃爍,顯
示畫面上將顯示預設的程序持續時間。
程序啟動約 15 分鐘後:
要暫停程序,請按啟動/暫停按鈕。
對應的標誌將開始閃爍。
-
再次按啟動/暫停觸控按鈕。程序將
繼續運作。
-
程序啟動後,只能更改部分選項。
按下啟動/暫停觸控按鈕。對應的標
誌將開始閃爍。
1.
更改選項
。
再次按啟動/暫停觸控按鈕。程序將
繼續運作。
3.
洗衣程序或預約功能運作時,機門將保
持緊鎖狀態,同時顯示畫面顯示「 」
標誌。首先按啟動/暫停觸控按鈕,將洗
衣機設為「
PAUSE
」(暫停)狀態。待
門鎖標誌熄滅後,即可將機門打開。
如果門鎖標誌「 」沒有消失,
表示洗衣機已經在加熱,並且水位高出
機門底邊,或者滾筒正在轉動。這種情
況下,機門將無法打開。如果您需要打
開它,你必須瀝乾水再開門。(請閱讀
「進行排水」章節)
㮦⿍濊
如果在程序正在運作時按下任何觸控
鍵,顯示畫面將顯示「 」消息,
並發出嗶嗶聲。(啟動/暫停觸控鍵和
電源開/關按鈕除外)
要更改正在運作的程序,只能關閉洗衣
機電源。
按電源開/關按鈕取消程序並關閉洗
衣機。
-
再次按電源開/關按鈕啟動洗衣機。
在此期間,洗衣機不會排水
(除了程序 蒸氣除皺、脫水、
洗清+脫水)。
-
此時即可設定新的洗衣程序。
當程序設計循環結束和防皺階段完成時
,在
Remote
( ) 功能的情況下啟動。
門會保持鎖定狀態 5 分鐘,如果你想在
那個時候開門,請按
Remote
( ) 觸控
板一次以關閉功能,則門會開鎖。
5.4 啟動程序( )
5.8 打開機門
5.9 程序結束
5.5 中斷程序
5.6 更改程序
5.7 更改選項
如果是緊急情況下需要立即打開
門。請閱讀第
83
頁的「緊急開
門」章節。
㮦⿍濊
2
.
Summary of Contents for EWW1142ADWA
Page 92: ...G0030937 001 A21791305 ...