www.electrolux.com
6
11
10
9
7
8
'BO
speed control
Change the fan speed by gently touching desired
fan speed icon on the product. You can also slide
your finger across the arc to change fan speed
(ref. picture 7).
Auto mode
Change to AUTO mode by gently touching icon
labeled A. You can bring product out of AUTO
mode by pressing any other icon except change
filter (ref. picture 8).
Sleep mode
Change to SLEEP mode by gently touching icon
labeled with a moon. You can bring product out
of SLEEP mode by pressing any other icon except
change filter (ref. picture 9).
While in SLEEP mode, the UI including the AQI
light will be turned off after X seconds.
Child lock
To enable CHILD LOCK long press icon labeled
with a lock for 5 seconds. When in this mode, no
other icon will register input (ref. picture 10).
To disable CHILD LOCK, long press icon labeled
with a lock again for 5 seconds till the lock LED
turns off.
Power off
Power down the product by gently touching the
ON/OFF icon on the center of the product
(ref. picture 11).
AIR QUALITY INDICATOR
The appliance has an air quality sensor that
analyzes the air quality.
The air quality light will show the real-time air
quality through different colors of light. As shown
below:
12
LIGHT'S COLOR
Blue
Green
Orange
Red
PM 2.5 (μg/m
3
)
AIR QUALITY
0-15
Very Good
16-35
Good
36-75
Bad
>75
Very Bad
FILTER CHANGE INDICATOR
The filter change indicator will light up to
remind you to change the filter
3FG&''$-/
.
• When filter change indicator flicker with red
light, please replace the filter and reset the filter
change indicator.
• When filter change indicator stop flicker and the
red light fix, please replace the filter immediately
and reset the filter change indicator.
13
14
Filter change indicator reset operation
Press the filter change button " "for 3s and filter
change indicator will reset, then red light will go
off.
STORAGE
ERROR CODE
If you are not planning to use the appliance for
a long time, cover it with plastic or return it to its
carton.
Fan failure error code, when digital display area
shows E1, it means the fan failure occurs. Motor
will stop working.
"JSRVBMJUZ
sensor failure error code, when digital
display area shows E2 after unit run
O
ing 10min
later, unit will keep running, it means the
"JS
RVBMJUZ
sensor failure occurs.
18
19
20
NOTE:
The multi-layer filter can not be washed, it
can only be replaced.
CAUTION!
Do not touch the fan blade when removing the
multi-layer filter.
CARE AND CLEANING
Unplug the appliance before cleaning to prevent
shock or fire hazards. Use a damp cloth or a
vacuum cleaner with soft brush to clean your air
purifier.
The plastic part of the cabinet and top may be
cleaned with an oil-free cloth or washed with a
cloth dampened in a solution of warm water and
mild liquid dishwashing detergent. Be sure to
wring excess water from the cloth before wiping
around the controls. Excess water in or around the
controls may cause damage to the appliance.
Never use harsh cleaners, wax or polish when
cleaning the unit.
15
17
16
Summary of Contents for FLOW A4
