16
Fitting/installation in working surface: surface mounting
(coated, lined, Inox or stone)
When fitting in combustible material the NIN 2000,
section 4.2.2 and the fire protection regulations, in
addition to the directives of the association of can-
tonal fire insurance companies, must be observed
without fail.
1
. The lateral spacing of the working surface cut-out
from a high-level cabinet and the rear wall must be
at least 50 mm.
2.
Cut out working surface according to specified
cut-out dimensions. The tolerances must be
observed. Seal the cut-out area of the working
surface against moisture with suitable varnish.
3.
Holes for the built-in switchbox in the front of the
cabinet with template as illustrated.
Panel thickness min. 16 mm, max. 22 mm.
4.
Guide the built-in switchbox with the bundle of
connecting conductors from above through the
working surfaces cut-out and from the rear to the
front of the cabinet.
Warning:
There are capillary tubes in the bunch
of conductors between the built-in switchbox and
the grill plate. Do not bend sharply or separate or
the appliance will be destroyed!
5a.Assembly with CN-front panel (CN)
Guide the signal lamps from the rear through the
12 mm dia. holes in the front of the cabinet (the
12 mm dia. holes can be enlarged to 15 mm to
simplify assembly). Take the switch spindle(s) of
the built-in switchbox from the rear through the
13 mm dia. hole(s) and insert the signal lamps in
the signal lamp lenses mounted on the CN front
panel from the rear.
– TY58: insert signal lamp with red wires in the
left-hand red lens.
– TY38: insert signal lamp with red wires in
upper red lens.
Screw CN-front panel with screws to front of cabi-
net under switch knobs. Attach switch knobes and
then secure built-in switchbox in front of cabinet
from rear
5b.Assembly without CN-front panel (Vi)
Insert the signal lamp lenses supplied from the
front in the 12 mm dia. holes of the front of the
cabinet.
– TY58: left-hand red lens.
– TY38: upper red lens.
Insert the signal lamps from the rear through the
front of the cabinet in the signal lamp lenses.
– TY58: insert signal lamp with red wires in the
left-hand red lens.
– TY38: insert signal lamp with red wires in
upper red lens.
Take the switch spindle(s) of the built-in switchbox
from the rear through the 13 mm dia. hole(s),
attach white or black switch knobs as required and
then secure the built-in switchbox from the rear to
the front of the cabinet.
6.
For tiled working surfaces the joints must be com-
pletely filled with jointing material in the supporting
zone for the grill plate.
7.
The enclosed sealing tape must be attached to
the underside of the grill plate.
8.
Clean the working surface thoroughly in the seal
supporting zone.
9.
Place grill plate in cut-out from above, centre and
press down firmly. It requires no additional fixing
owing to its own heavy weight.
Please do not apply any additional silicone sealing
compound, since in the event of removal of the
grill plate both the seal and the working surface
could be damaged.
Warning:
If not fitted correctly it would be difficult
to remove for servicing and the grill plate and
working surface could be damaged.
Warning:
A recess base which can be dismantled
must be fitted as contact protection under the grill
plate/built-in switchbox.
Removing the grill plate
1.
Remove power supply from built-in switchbox/grill
plate.
2.
Place a clean spatula as protection on the working
surface. Then carefully run a firmer chisel under
the edge of the grill plate and raise.
3.
For a new fitting it must be ensured that the old
seal is removed completely cleanly and a new
seal fitted (available from spare-parts sales).
Removing the built-in switchbox (for servicing)
1.
Remove power supply from built-in switchbox and
dismantle the recess base.
2.
Pull off switch knobs (if present remove CN front
panel forwards). Withdraw signal lamps from the
lenses from the rear, release fixing screws of built-
in switchbox on the front of the cabinet from the
rear, draw the switchbox forwards carefully
through the opening in the recess base. Re-fitting
is performed according to the fitting/installation
text.
Warning:
There are capillary tubes in the bunch
of conductors between the built-in switchbox and
the grill plate. Do not bend sharply or separate or
the appliance will be destroyed.
