background image

Page 15 of 24                                                                                                                                  M6493 Issue 10.3 

 

7.11. 

Configuring Parameters. 

 

7.11.1. 

To select the parameter, enter Programming mode press 

 

and

 

 

button for 5 seconds.  

Use the 

 and 

 buttons to select the parameter for modification.  

Press the 

 button to display the value. 

By keeping the 

 button pressed, use the 

 and 

 buttons to 

set the desired value. 

When the 

 button is release, the newly programmed value will be stored. 

The newly programmed value is stored and the following parameter is displayed. 

To exit from the setup, press the 

 or wait for 30 seconds. 

 

 

PAR 

RANGE 

DESCRIPTION 

SCL 

1°C; 
2°C; 
°F 

Read out scale (see table of input specifications) 
Caution: upon changing the SCL value, it is the absolutely necessary to reconfigure the 
parameters relevant to the absolute and relative temperatures (SPL, SPH, 1SP, 1HY ect…). 
 

SPL 

-50°..SPH 

Minimum limit for 1SP setting. 
 

SPH 

SPL..150°C 

Maximum limit for 1SP setting. 
 

1SP 

SPL..SPH 

Set-point (value to be maintained in the room). 
 

1CM 

HY;PID 

Control mode. 
With 1CM=HY you select control with hysteresis: parameters 1HY, 1T0 and 1T1 are used. 
With 1CM=PD you  select a Proportional-Integral-Derivative control mode: parameters 1PB, 1IT, 
1DT, 1AR, 1CT will be used. 
 

1CH 

REF;HEAS 

Refrigerating (REF) or Heating (HEA) control mode. 
 

  

  

  

  

  

  

  

  

  

  

  

  

  

  

1

C

M

=

H

Y

 

1HY 

0…19.9°C 

OFF/ON thermostat differential. With 1HY =0 the output is always off. 
 

 

1TO 

0…30min 

Minimum off time. 
After output 1 has been turned off’ it remains inactive for 1TO minutes regardless of the 
temperature value measured. 

1T1 

0…30 min 

Minimum on time. (The following parameter will be 1PF). 
After output 1 has been turned on, it remains active for 1T1 minutes regardless of the 
temperature value measured. 

1

C

M

=

PI

D

 

1PB 

0.19.0°C 

Proportional bandwidth. 
 
Temperature control takes place by changing the 
ON time o the output: the closer the temperature to 
the set-point, t he less time to activate. A small 
proportional band increases the promptness of the 
response of the system to temperature variations, 
but tends to make it less stable. A purely 
proportional control stabilises the temperature 
within the proportional band but does not cancel 
the deviation from the set-point. 
With 

1PB=0

 the output is always off. 

 

 

Summary of Contents for MC810B MKII

























Reviews: