background image

Page 9 of 20                                                                                                                                     M6847 issue 1.1 

6.  ENVIRONMENTAL PROTECTION. 

 

 

6.1. 

Packaging materials have been selected such that they may be sorted for 

recycling. 

 

6.2. 

 At the end of your product and accessories life, it must not be discarded as 

domestic waste. Ref: EU Directive 2002/96/EC on Waste Electrical and Electronic 
Equipment Directive (WEEE). Please contact your distributor / supplier for further 
information. For end users outside of the EU consult applicable regulations. 

 

6.3.  This product should only be dismantled for recycling by an authorised recycling 

company.  

 

This product and accessories must be accompanied by a completed 

Decontamination Certificate prior to any disposal.

 

Copies of the Certificate are 

available from your distributor of Bibby Scientific products, or you may copy 
and enlarge from ‘Appendix A’ of this instruction book. 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Bibby Scientific’s Electrothermal branded product range is registered with the Environment Agency under the name of as 
Electrothermal Engineering Limited as being a producer of WEEE (Waste Electronic and Electrical Equipment) through b2b 
Compliance

,

 an authorised waste collection compliance scheme. 

Summary of Contents for MH8517




















Reviews: