Elektra Beckum SPA 1100, Assembly And Operating Instructions Manual

ENG

7

General

The SPA 1100 chipping suction device is suitable for
vacuuming planing, milling and sawing chippings, as well
as wood dust.

The entire machine assembly is packed in a packaging
unit.

If after reading these operating instructions, you should
have further queries about the SPA 1100 chipping suc-
tion device, please contact the:

Elektra Beckum AG, Customer Service,

Postfach 13 52, D-49703 Meppen.

We supply 12 months guarantee this for products in ac-
cordance with the legal/country specific regulations.
Please make sure that the guarantee is valid from the
date of purchase and can be proven by means of a re-
ceipt.
Damage which occurs as a result of natural wear, over-
load, improper use or negligence of maintenance work
is not covered by our guarantee.
Complaints can only be accepted if the apparatus/the
machine is returned to your dealer in one piece (with all
accessories) or the complaints are registered there im-
mediately.

Product liability/guarantee

The SPA 1100 chipping suction device may only be used
for its intended purpose.
Possible applications not described in these operating
instructions require the written consent of Elektra
Beckum AG.

Proper use

The SPA 1100 chipping suction device serves to vacuum
planing, milling and sawing chippings (only wood and
plastics) or wood dust on work working machinery.
Any other use is considered unacceptable. We are not
liable for any damage resulting from any alterations to
the SPA 1100 chipping suction device caused by such
improper use, or carried out by the user himself.
Flammable gases (e.g. paint fumes) and explosive me-
dia may not be vacuumed.
Use in industrial firms, in technical colleges and schools,
etc. is not permitted.

Safety notes

When improperly used electrical machines may lead to
dangerous situations. Therefore, please always observe
the safety notes below.

•

In case of malfunctioning, immediately pull out the
plug. Never switch on the machine without the dust
bag.

•

Never allow children or young people to operate the
machine.

•

Never use the machine if the electrical motor, on/off
switch, fan casing or connection cable is damaged.

•

Never vacuum any sources of ignition.

•

Only use the machine to vacuum wood working
machines.

Assembly

Fig.

: Place fan housing 

2

 with motor facing down on

workbench or other sturdy support and use a
wooden block or similar to support it in a level
position.
Attach side panels 

3

 and 

4

, with labels facing

outward, with thread cutting screw 

1

 supplied to

the fan housing.

Fig.

: Install cross plate 

5

 with cup square neck screws,

washers and hexagon flange nuts between side
panels.

Fig.

: Install a castor socket on each corner of the

base plate. Fit three each cup square neck
screws 

6

 M 5 x 20 through bottom panel and

castor socket 

7

, and secure with washers 

8

 and

hexagon flange nuts 

9

. Afterwards push twin

caster 

10

 into castor socket.

Fig.

: Put the so pre-assembled base plate onto the

side panels as shown, and secure with cup
square neck screws and hexagon flange nuts.
Afterwards check that all screw connections are
tight and stand machine on the casters.

Fig.

: Fit hose clamp 

11

 to end of suction hose 

12

,

then push hose on the suction port below the
motor, tighten hose clamp.

Fig.

: Fit dust bag 

14

 to dust collection opening.

Use dust bag of appropriate size (e. g. 600 x 900
mm), and clamp to opening with tightening strap

13

.

Tip:

 Fit opening of dust bag tight around dust

collection opening and fold overlapping section.
Pull tightening strap over it and tighten.

Fig.

: Bent the two flexible rods 

15

 into a “U“ and fit

their ends into the four holes on the neck of the
housing’s filter bag opening.
At the vertex secure the rods crosswise with a
cable tie.
Fit dust bag 

16

 and tightening strap 

17

 over the

filter bag opening and tighten strap.

1

2

3

4

5

6

7