15. SETTINGS MENU
66
If MIDI+USB is selected in the OUTPUT TO settings, MIDI data will limit the USB speed.
When sending large chunks of data, make sure you only use the USB setting.
OUTPUT CH
selects whether the knobs will send data on the auto channel or the track channel.
PARAM OUTPUT
selects what type of MIDI messages the
DATA ENTRY
knobs will send. For information
about which CC/NRPN parameters that will be sent, please see “APPENDIX A: MIDI” on page 77.
•
NRPN
will make the knobs send out NRPN MIDI messages.
•
CC
will make the knobs send out CC MIDI messages.
ENCODER DEST
controls whether the
DATA ENTRY
and
LEVEL/DATA
knobs sends MIDI data or not.
When set to INT, the knobs only affects the Digitakt and no MIDI data is sent. When set to INT + EXT,
the knobs affects the Digitakt and also sends MIDI data to external devices.
TRIG KEY DEST
controls whether the
[TRIG]
keys sends MIDI data or not. When set to INT, the
[TRIG]
keys only affects the Digitakt and no MIDI data is sent. When set to INT + EXT, the
[TRIG]
keys
affects the Digitakt, and also sends MIDI data to external devices. When set to EXT, the
[TRIG]
keys
do not affect the Digitakt but MIDI data is sent externally.
MUTE DEST
controls whether activating/deactivating mutes will send MIDI data or not. When set to
INT, mute only affects the Digitakt and no MIDI data is sent. When set to INT + EXT, mute affects the
Digitakt and also send MIDI data to external devices. When set to EXT, mute sends MIDI data exter-
nally, but do not affect the Digitakt.
RECEIVE NOTES
will, when active, make it possible to play Digitakt using an external MIDI keyboard.
RECEIVE CC/NRPN
will, when active make it possible to control Digitakt parameters from an external
MIDI device sending CC/NRPN data.
15.3.3 CHANNELS
This menu handles the MIDI channel configuration.
TRACK 1–8
selects the dedicated MIDI channel that is used to receive or send (by turning the knobs)
parameter data to or from a specific audio track. If configured as OFF, parameter data are neither
received nor sent via MIDI.
TRACK A–H
selects the dedicated MIDI channel that is used to receive or send (by turning the knobs)
parameter data to or from a specific MIDI track. If configured as OFF, parameter data are neither
received nor sent via MIDI.
•
The sequencer data is always sent on the MIDI channel specified by the CHAN
parameter on the SRC PARAMETER page.
•
On TRACK A-H you can only control the parameters on the TRIG (NOT1, VEL, LEN,
LFO.T) and LFO (all) PARAMETER pages.
FX CONTROL CH
selects the dedicated MIDI channel that is associated with the parameters on the
DELAY and REVERB parameter pages, both for input and output. If configured as OFF, parameter
data are neither sent nor received via MIDI.
AUTO CHANNEL
selects the MIDI channel that will give access to the currently active track. If an ex-
ternal MIDI keyboard connected to Digitakt sends MIDI data on this channel, the keyboard will control
the active track. This is useful when for example quickly changing between the active audio tracks
to play different Sounds. The Digitakt also uses the AUTO channel to record to the MIDI tracks from
external MIDI controllers.
PROGRAM CHG IN CH
selects the MIDI channel that will listen for incoming program change mes-
sages. An AUTO setting will use the AUTO channel. Enable Digitakt to respond to program change
messages in the MIDI SYNC menu. For more information, please see “15.3.1 SYNC” on page 64.
Summary of Contents for Digitakt
Page 1: ...Digitakt User Manual...
Page 84: ...4116ENG O...
