42
Instrukcja obs
ł
ugi i monta
ż
u HRD FU-ATEX
www.elektror.pl
PL
9016330 01.20/08
Uwaga!
Ś
ruba oko na silniku nie wolno stosowa
ć
do pod-
noszenia ca
ł
ego dmuchawy. To jest stosowane
wówczas, gdy silnik musi by
ć
jest zamontowana.
2.2 Sk
ł
adowanie
• Upewni
ć
si
ę
,
ż
e przy
łą
cze ssania i przy
łą
cze ci
ś
nieniowe
s
ą
zamkni
ę
te.
• Odstawi
ć
wentylator
-> w miar
ę
mo
ż
liwo
ś
ci w oryginalnym opakowaniu
-> w zamkni
ę
tym pomieszczeniu
-> w miejscu suchym, wolnym od py
ł
u i drga
ń
.
• Zakres temperatury sk
ł
adowania od -20°C do +60°C
• Po 6 miesi
ą
cach sk
ł
adowania, przed zamontowaniem wen-
tylatora, sprawdzi
ć
ł
o
ż
ysko wentylatora lub
ł
o
ż
ysko silnika.
3 INFORMACJE O WPROWADZENIU
MASZYNY DO EKSPLOATACJI
3.1 Zasady podstawowe
•
Przed pierwszym i ka
ż
dym ponownym uruchomie-
niem zespo
ł
u nale
ż
y dok
ł
adnie sprawdzi
ć
, czy jest on w
prawid
ł
owym stanie. Nie wolno eksploatowa
ć
zespo
ł
ów, u
których np. przy odbiorze lub podczas instalacji stwierdzo-
no uszkodzenia.
• Ustawienie, monta
ż
, eksploatacja i konserwacja mo
ż
e
by
ć
wykonywana tylko przez regularnie szkolony perso-
nel techniczny o odpowiednich kwali
fi
kacjach i uprawni-
eniach. Eksploatacja po wadliwym monta
ż
u, konser-
wacji lub nieuzgodnionej wymianie cz
ęś
ci skutkuje
u
ż
ytkowaniem niezgodnym z przeznaczeniem i powoduje
utrat
ę
gwarancji. Zwi
ą
zane z tym ryzyko ponosi wy
łą
cznie
klient lub u
ż
ytkownik.
Uwaga!
Nale
ż
y zapewni
ć
niezawodn
ą
ochron
ę
przed wni-
kaniem do wentylatora cz
ą
stek obcych, rdzy, rdzy
nalotowej i innych tlenków
ż
elaza.
3.2 Ustawianie, monta
ż
• Podczas ustawiania, monta
ż
u i pó
ź
niejszej eksploatacji
wentylatora nie nara
ż
a
ć
go na drgania, wstrz
ą
sy i
uderzenia.
• Otwarte kró
ć
ce wlotowe i wylotowe os
ł
oni
ć
kratkami
ochronnymi wed
ł
ug normy DIN EN ISO 13857.
Pomiar na os
ł
onie
ł
o
ż
yska ko
ł
nierza, je
ś
li to mo
ż
liwe
w pobli
ż
u
ł
o
ż
yska
= Punkt
pomiarowy
= Kierunek
pomiaru
Maksymalnie dopuszczalna pr
ę
dko
ść
drga
ń
(Warto
ś
ci graniczne zgodnie z ISO 14694:2003 (E),
kategoria BV-3)
Zamontowane na
sztywno
[mm/s]
Zamontowane
elastycznie
[mm/s]
Warto
ść
skuteczna
[r.m.s.]
Warto
ść
skuteczna
[r.m.s.]
W zabudowie
Rozruch
4,5
6,3
Alarm
7,1
11,8
Wy
łą
czenie
9,0
12,5
3.3 Pod
łą
czenie elektryczne
Uwaga!
Prace opisane w tym podrozdziale mog
ą
by
ć
przeprowadzane tylko przez wykwali
fi
kowanych
elektryków. Dobra
ć
wymiary i dokona
ć
wyboru
przewodów przy
łą
czeniowych oraz wykona
ć
pod
łą
czenie silnika wed
ł
ug schematu po
łą
cze
ń
w
skrzynce zaciskowej oraz zgodnie z w
ł
a
ś
ciwymi
lokalnymi przepisami.
• Wykonanie instalacji elektrycznej musi spe
ł
nia
ć
wymagania normy EN 60079-14.
• Nale
ż
y zapewni
ć
pe
ł
ne wyrównanie potencja
ł
ów, tzn.
dostateczne, w
ł
a
ś
ciwe i fachowe uziemienie wszystkich
cz
ęś
ci przewodz
ą
cych pr
ą
d elektryczny.
• Sprawdzi
ć
, czy napi
ę
cie sieciowe odpowiada parametrom
podanym na tabliczce znamionowej.
• Jako silniki nap
ę
dowe stosowane s
ą
wy
łą
czne silniki
indukcyjne trójfazowe w wykonaniu przeciwwybuchowym.
• Przy
łą
cze przewodu ochronnego znajduje si
ę
w skrzynce
zaciskowej.
• Nale
ż
y przestrzega
ć
dodatkowych informacji producenta
silnika i falownika, które znajduj
ą
si
ę
w doku-
mentacjach dostawców.
3.3.1 Szczególne wskazówki dotycz
ą
ce pracy
wentylatorów ATEX z przemiennikiem
cz
ę
stotliwo
ś
ci
Uwaga!
Z przemiennikiem cz
ę
stotliwo
ś
ci mog
ą
pracowa
ć
tylko silniki ognioszczelne i wzmocnione ozna-
czone Ex db eb II2GD T4 135°C!