background image

 

 

7. TROUBLES-CAUSES-TROUBLESHOOTING 

Trouble 

Cause 

Troubleshooting 

Engine will not 

start 

1.

 

Empty tank 

2.

 

fouled air filter 

3.

 

no ignition spark 

4.

 

flooded engine 

1.

 

fill in the tank, check the fuel in 

carburetor, defecate the tank and 

clean the hole in the lid with a needle 

2.

 

clean the air filter 

3.

 

clean the ignition plug or use a new 

one, check the ignition cable, have the 

ignition system checked in a servicing 

shop 

4.

 

remove the plug, clean and wipe dry, 

pull the starting cable several times 

with the plug removed 

Faltering engine   

1.

 

ignition cable detached 

2.

 

fuel piping clogged or 

wrong fuel 

3.

 

blocked hole in the fuel 

tank cover 

4.

 

water or dirt in fuel 

system 

5.

 

fouled air fitter 

1.

 

push the plug, socket firmly on the 

plug 

2.

 

clean fuel piping, use fresh/different 

fuel replace the fuel tank cover 

3.

 

drain the fuel and refuel 

4.

 

clean the air filter 

Engine often 

switches off when 

idling 

1.

 

too long ignition interval, 

defective ignition plug 

2.

 

carburetor not set 

correctly 

3.

 

fouled air filter 

1.

 

adjust/replace the ignition plug 

2.

 

set up the carburetor 

Drive will not 

work properly 

1.

 

check the drive lever 

cable tension 

2.

 

drive does not work 

1.

 

adjust the cable tension if necessary 

2.

 

have the unit checked in a servicing 

shop 

Excessive 

vibrations 

1.

 

loose lock screws 

1.

 

tighten the lock screws 

 

 

 

 

 

Summary of Contents for MTBT59-CC139L





















Reviews: