Elenco Electronics M-2665K Assembly And Instruction Manual Download

Page: 18 / 18

PARTS LIST - SECTION D

Qty

Symbol

Description

Part #

PTC

Ω

Thermister

190415

ASSEMBLE THE FOLLOWING COMPONENT TO THE PC BOARD

The other components for this section have been installed already.

SECTION D

Resistance Circuit

-17-

Testing Procedure

Connect the 9V battery and test leads to the meter
(red to V

Ω

and black to COM).

Set the range

selector knob to one of the Ohm scales. Make sure
that SW1 is in the DC/Ohm position. Using two or
three different value resistors, check each scale.
Compare the kit meter readings with another meter

of known accuracy. If the tests are not working,
check for cold solder joints, part values, and the
contacts on the selector knob to make sure that they
are intact. Turn the meter off and remove the battery
and test leads.

-18-

PARTS LIST - SECTION E

RESISTORS

Qty.

Symbol

Description

Color Code

Part #

98.8

Ω

1% 1/4W

white-gray-gray-gold-brown

129830

R37

150

Ω

5% 1/4W

brown-green-brown-gold

131500

900

Ω

1% 1/4W

white-black-black-black-brown

139030

R41

1.91k

Ω

1% 1/4W

brown-white-brown-brown-brown

141930

R40

4.12k

Ω

1% 1/4W

yellow-brown-red-brown-brown

144130

Ω

1% 1/4W

white-black-black-brown-brown

149030

R38

10k

Ω

1% 1/4W

brown-black-black-red-brown

151030

R43

11k

Ω

1% 1/4W

brown-brown-black-red-brown

151130

R39, R42

39.2k

Ω

1% 1/4W

orange-white-red-red-brown

153930

R44

76.8k

Ω

1% 1/4W

violet-blue-gray-red-brown

157630

R10

90k

Ω

1% 1/4W

white-black-black-red-brown

159030

R45

158k

Ω

1% 1/4W

brown-green-gray-orange-brown

161530

R14, R15

240k

Ω

5% 1/4W

red-yellow-yellow-gold

162400

OR red-yellow-black-orange-green

R11

909k

Ω

1% 1/4W

white-black-white-orange-brown

169060

VR2

200

Ω

/ 220

Ω

Potentiometer

191320

Note:

Resistor tolerance (last band) of 5-band resistors may be green instead of brown.

CAPACITORS

Qty.

Symbol

Value

Description

Part #

C10 - C13

.01

F (103)

Mylar

241017

SEMICONDUCTORS

Qty.

Symbol

Value

Description

Part #

324 / 17324

Integrated Circuit

330324

D3 - D6

1N4001 or 1N4007

Diode

314001

D11

1N4148

Diode

314148

MISCELLANEOUS

Qty.

Symbol

Description

Part #

, CX

9-pin Socket

664009

IC Socket 14-pin

664014

SECTION E

Capacitance and Transistor Testing Circuit

PTC - Thermister 1k

Ω

Mount part in holes shown only

DO NOT PROCEED TO SECTION E WITHOUT INSTRUCTOR’S APPROVAL.

Summary of Contents for M-2665K



















Search results

Summary of Contents for M-2665K

Reviews:

Related manuals for M-2665K

Brands by name

Popular brands

Elenco Electronics M-2665K, Assembly And Instruction Manual

Search results

Summary of Contents for M-2665K

Reviews:

Related manuals for M-2665K

Brands by name

Popular brands