elero SunTop, Operating And Assembly Instructions Manual

5.3  Connection example SunTop 230 V/50 Hz 

PE

N

L1

1 0 2

sw

br

bl

gr/

ge

1

2

3

4

7

6

Wicklungsthermostat

Geräteschalter

Abzweigdose

Schalterdose

Jalousieschalter/Jalousietaster

Elektronik

Kondensator

sw schwarz
br braun
bl blau
gr/ge grün/gelb

L1,N,PE  Netz 230V/50Hz

1

2

3

4

5

6

5

7

Illustration, left: Plug connection (drive side) 

Illustration, right: Coupling connection (mains supply) 

1 blue (neutral conductor) 

2 black 

3 brown 

  Green-yellow

Fig. 4    Connection diagram SunTop 230 V/50 Hz and cable 

assignment when using Hirschmann plug connec-

tion STAS-3 

Important 

The motor controls in the up/down direction must be locked 

against each other. 

5.4  Parallel circuit 

Important 

You can connect several SunTop drives in parallel. Please 

note the maximum switching capacity of the control unit. 

5.5  Commissioning 

Important 

The drive is in commissioning mode when delivered. 

►

The end positions must be adjusted using the 

elero

assembly cable 

►

The assembly cable may only be connected to commis-

sion the drive and for adjustment operations

%ODX1HXWUDOOHLWHU

6FKZDU]

%UDXQ

*UQJHOE

HOHUR

%ODX1HXWUDOOHLWHU

6FKZDU]

%UDXQ

*UQJHOE

Fig. 5  Connection for assembly cable 

►

Switch on mains. 

►

You can now set the end positions with the 

elero

 assem-

bly cable. 

1

 Winding thermostat 

2

 Electronics 

3

 Junction box 

4

 Switch box 

5

  Interlocked venetian 

blind push button/switch 

6

 Drive 

7

 Capacitor 

sw

black 

br

brown 

bl

blue 

gr/ge

green/yellow 

3

2

1

6 | EN  

© 

elero

 GmbH 

Assembly: Electrical connection | Adjusting the end positions 

5.2  Electrical connection 

WARNING 

Faulty electrical connections constitute a fatal hazard. 
Risk of electric shock. 

►

Prior to initial commissioning, check the PE wire is cor-

rectly connected. 

ATTENTION 

Damage to the SunTop due to incorrect electrical 

connection. 

►

Prior to initial commissioning, check the PE wire is 

correctly connected. 

Ingress of moisture will damage or even destroy the 

SunTop. 

►

For devices with protection class IP44, the customer-side 

connection of the cable ends or plugs (cable feed-

through) can also be implemented according to protection 

class IP44. 

Damage or destruction of the SunTop for variants with  

230 V 1 AC due to incorrect activation. 

►

Switches with an OFF presetting (dead-man's switches) 

for drives are to be attached within visible range of the 

SunTop but away from spontaneously moving parts and 

at a height of more than 1.5 m. 

Damage to the blind due to incorrect travel direction. 

►

The assignment of the UP/DOWN travel direction must 

be checked after the electrical connection has been 

established. 

Misalignment of the end positions on the drive. 

►

Misalignment of the end positions is indicative of a faulty 

electrical connection. Readjusting the end positions is not 

sufficient in this scenario as the end positions will simply 

become misaligned again. The drive must then be re-

placed and the cause of the problem rectified. 

Important 

All applicable standards and regulations must be observed 

during the electrical installation. 
If the drive is connected to a control unit, the operating 

instructions for the control unit must be observed. 
There is generally no need to plug the connecting cable 

and plug in and out again for the electrical connection. 
Depending on the mounting or adapter plate used, the 

plate will need to be removed prior to cable replacement. 

This applies in particular to the SunTop type S. 

Connect only in de-energised state. To do this, switch 

the drive cable so it is de-energised. 

1  Press locking mechanism on the motor cable plug to-

wards the cable using a screwdriver. 

2  

Pull out the plug. 

3  

Insert the motor cable plug until the lock engages.