5.6 Setting of end positions and strain relief
Important preliminary consideration:
The relief for an end position produces a low material load
on the drive and blind. It counteracts the tensile forces act-
ing on the blind at the upper end position and the compres-
sive forces acting on the lower end position by momentarily
changing the travel direction.
Decide on a specific relief function before setting the end
position (different combination options as per the following
designs):
This will save you unnecessary configuration outlay!
With the assembly cable connected, press one of the travel
keys until the drive signals the transition to programming
mode by a short, automatic stop. You can now program the
end positions. The setting mode is finished after both end
positions have been set.
5.6.1 Relief function for end position(s)
If an end position was taught in at a limit stop, a relief can
also be enabled for the blind.
Important
The relief function (for variants B to D) is activated in one
step when programming the end positions (see chapters
5.6.7 to 5.6.9)!
5.6.2 Relief function at upper end position
For variant B (see chapter 5.6.7)
and variant C (see chapter 5.6.8):
Activate relief function at upper end position
1
Use the assembly cable while holding down the
UP
button ▲ from instruction
①
(chapters 5.6.7 and
5.6.8) to also press the
DOWN
button ▼ (simul
-
taneously), and hold down both buttons until the
blind stops.
The relief function at the upper end position is activated.
5.6.3 Relief function at lower end position
For variant C (see chapter 5.6.8) and variant D
(see chapter 5.6.9):
Activate relief function at lower end position
1
Use the assembly cable while holding down the
DOWN
button ▼ from instruction
③
(chapters
5.6.8 and 5.6.9) to also press the
UP
button ▲
(simultaneously), and hold down both buttons until
the blind stops.
The relief function at the lower end position is activated.
5.6.4 Changing/deleting the end positions and
deleting the relief function
It is not possible to change or delete individual end posi-
tions. This is always done in pairs (upper and lower end
position simultaneously).
When the end positions are deleted, the setting for the
optional relief function will also be discarded.
Important
The blind protection system is only adapted to the blind
after a complete, uninterrupted upwards and downwards
travel.
Changing/deleting the end positions
1
Starting from a central position of the blind, use the
assembly cable to simultaneously press both direc-
tion buttons (▲ and ▼), and hold them down until the
drive briefly moves up and down.
The end position settings have been deleted.
The end positions may be readjusted.
5.6.5 Four variants of end position settings
Four combinations of end position settings can be chosen.
End position settings (4 variants)
A
Upper and lower end position freely adjustable
B
Fixed upper end position, lower end position freely
adjustable
C
Fixed upper and lower end position
D
Upper end position freely adjustable, fixed lower end
position
Fig. 6 End position setting variants for the SunTop
5.6.6 Variant A: Upper and lower end position
freely adjustable
Variant A:
Upper and lower end position freely adjustable
①
Starting from a central position of the blind, press
the
UP
button▲ with the assembly cable until the
blind has reached the desired upper end position.
The drive begins to travel, briefly stops and travels
further (for as long as the UP button ▲ remains
pressed).
Corrections are possible using the ▲ and ▼ buttons.
②
Press the
DOWN
button ▼ until the drive stops
automatically.
The upper end position has been set.
③
Press the
DOWN
button ▼ again until the blind has
reached the desired lower end position.
The drive begins to travel, briefly stops and travels
further (for as long as the
DOWN
button ▲ remains
pressed).
Corrections are possible using the ▲ and ▼ buttons.
④
Press the
UP
button ▲ until the drive stops auto
-
matically.
The lower end position has been set.
Adjustment of the variant A end position is complete.
Fig. 7 End position setting, variant A:
©
elero
GmbH
EN | 7
End position adjustment | Relief function
