background image

Warnhinweise

USA-13

USA-14

US

A

Battery replacement

1. Open the battery compartment.

2. Remove the batteries.

3. Insert the new batteries 

properly

.

Cleaning

Clean the device with a damp cloth only.

Do not use a cleansing agent as doing so may damage the plastic.

Troubleshooting

Problem

Cause

Remedy

Drive is not

1. Batteries are empty.

1. Replace batteries.

functioning.

2. Batteries are inserted

2. Remove batteries 

Transmission control 

incorrectly.

and re-insert

light is not illuminated.

properly.

Drive is not

1. Receiver is not within 

1. Move receiver closer 

functioning.

radio operating range.

to ensure it is within

Transmission control 

operating range.

light is illuminated.

2. Transmitter is not

2. Programme 

programmed in receiver.

transmitter.

Transmission control 

Battery power is low.

Replace batteries.

light is flashing.

Selected drive is not

Wrong group has been  

Select the correct

functioning.

selected.

group.

Drive moves in wrong  The directions have 

Delete transmitter and 

direction.

been set incorrectly.

re-programme correctly.

General declaration of conformity:

The company elero GmbH hereby declares that the VarioTel-915
handheld transmitter complies with the basic requirements and
other relevant regulations of the EC Directive 1999/5/EG.

Battery replacement/Cleaning/Troubleshooting

Summary of Contents for VarioTel-915









Reviews: