background image

©2014 Eley Corporation   PO Box 22640    Lincoln, NE  68542-2640      Rev. 04/14

Patents and Patents Pending   (Manual Part # 4075)

Model:  

1042

         

 Serial # ____________________

Purchase Date:_________________________________

Purchased From:________________________________

10 Year Warranty

Coverage

Eley Corporation guarantees this hose reel, components and parts, unless otherwise specified, 

to be free from defect, malfunction or failure in material, or workmanship, under normal use 
and service, for a period of 10 years(120 months).  Warranty period starts from original invoice 

date.  In the event of a defect or component failure, Eley Corporation will replace the specific 

component(s) free of charge.  

Exemptions

Warranty does not cover leaking due to damage caused by the use of acid, harsh chemicals 
or mineral deposits. Warranty does not apply when products are used in excess of their 
rated capacities and design functions or under abnormal conditions. The effects of corrosion, 

and normal wear and tear are specifically excluded from this warranty. This warranty does 

not cover damage which occurs in shipment or failures which are caused by products 
not supplied by the warrantor or failures which result from accidents, mishandling, faulty 
installation, freezing, misuse or misapplication, abuse or neglect.  Warranty is void if the 
product or any part thereof has been tampered or altered in any manner, or damage that is 
attributable to acts of God.  Eley Corporation covers the replacement or credit of defective 

parts only and does not allow for field labor charges for removal, installation, analysis or 

travel expenses.  In no event shall Eley Corporation or its suppliers be liable for any damages, 
whatsoever, arising out of the use of or inability to use this product. (Some states do not 
allow the exclusion of limitation of incidental or consequential damages, so the above 
limitation or exclusion may not apply to you). Eley Corporation and its suppliers disclaim all 
other expressed or implied warranties. Some states do not allow limitations on how long an 
implied warranty lasts, so the above limitation may not apply to you. This warranty gives you 

specific legal rights, and you may also have other rights which vary from state to state.

Summary of Contents for 1042













Reviews: