ELICA EPC632SS, Use, Care And Installation Manual

17 

Controls 

Use the high suction speed in cases of concentrated kitchen 
vapours.  It is recommended that the cooker hood suction is 
switched on for 5 minutes prior to cooking and to leave in 
operation during cooking and for another 15 minutes 
approximately after terminating cooking.  

Note:

  Hood retains last speed setting when aspiration 

switch is turned off. 

Description of control panel 

 
1. Light Button 

•  Press lamp button to turn ON the light on High 

Intensity (Lamp state previously OFF). 

•  Press lamp button to turn ON the light on Low 

Intensity (Lamp state previously ON). 

•  Press lamp button to turn OFF the light (Lamp state 

previously ON). 

2. Timer Button 

•  The default timer setting is 10 minutes, and it can be 

adjusted between 60 minutes and 1 minute. 

• 

After pressing the timer button, the control enters to a 
timer setup mode, and user can adjust the timer 
countdown time with the “+” and “-” buttons within 5 
seconds. The timer can be initiated immediately 
pressing the timer button, after setting the timer 
duration or pressing the timer button twice (default 10 
minutes setting). 

•  If no action occurs within 5 seconds, the countdown 

will start. 

•  During the timer setup the “+” and “-” buttons are 

dedicated to the timer and no motor action will occur. 

•  Once the timer is initiated, it can be cancelled by 

pressing the timer button again. 

3. Display 

• 

Shows the hood settings. 

•  The display will be lit at low intensity when the hood 

is not operating.   

Pressing any key the display will light up at high 
intensity.

•  The display will be lit at high intensity when the hood 

is operating. 

If no key is pressed within a minute the display will 
return to being lit at low intensity.  

4. “-” Button. Speed Decrease / OFF 

•  This button is used to decrease the fan speed, or 

turn OFF the fan. 

•  The fan will turn OFF if the “-” button is pressed and 

the hood was in the first speed. 

•  If the fan is at second speed and the “-” button is 

pressed, the fan will be set to first speed. 

•  If the fan is at third speed and the “-” key is pressed, 

the fan will be set to second speed. 

•  If the fan is at fourth speed and the “-” button is 

pressed, the fan will be set to third speed. 

•  If the fan is OFF and the “-” button is pressed, the 

control backlight will light up. 

5. “+” Button. Speed Increase / ON 

•  This button is used to increase the fan speed, or turn 

ON the fan. 

•  The fan will turn ON if the “+” button is pressed and 

the hood was OFF. 

•  If the fan is at first speed and the “+” button is 

pressed, the fan will be set to second speed. 

•  If the fan is at second speed and the “+” button is 

pressed, the fan will be set to third speed. 

•  If the fan is at third speed and the “+” button is 

pressed, the fan will be set to fourth speed. 

•  If the fan is at fourth speed and the “+” button is 

pressed, a beep will sound. 

Clock programming 

•   The clock can be reprogrammed at any time except 

during an active timed function. 

•   The clock can be displayed in a twelve hour format and 

valid clock times are from 1:00 to 12:59. 

•   The clock can be reprogrammed pressing the “

Timer

” 

button for 3 seconds, and after, the clock can be 
adjusted with the “+” and “-” buttons. 

•   The user can have minute increments / decrements of 1 

minute, but if the user keep pressing the “+” / ”-” buttons 
for more than 1 second, the increments / decrements will 
be of 5 minutes.  

During this option the control will round to the nearest 5 
minutes. 

•   The user can finish on reprogramming the clock pressing 

the “

Timer

” button. 

•   After 1 minute of no button pressed the control will 

accept the programmed clock time and will add one 
minute to the set clock. 

Grease filter saturation alarm (Optional) 

•   After thirty fan functional hours, the display will show 

“

Grease Filter

” if the fan is active.  

When this icon is shown in the display, the grease filters 
installed are required to be washed. 

•   To reset the grease filter saturation alarm the user must 

press the “+” button for 5 seconds, after this action the 
icon “

Grease filter

” is not displayed, and the hood has 

the normal display operation. 

Charcoal filter saturation alarm (Optional) 

•   After one hundred and twenty functional hours of the fan, 

the display will show “

Charcoal Filter

” if the fan is 

active. When this icon flashes on display, the charcoal 
filters installed are required to be replaced or 
reactivated. 

•   To reset the charcoal filter saturation indication the user 

must press the “-” button for 5 seconds, after this time 
the icon “

Charcoal filter

” is not displayed and the hood 

has the normal display operation. 

Audible signal activation and deactivation 

•   The audible signals can be activated or deactivated 

pressing the “

Light

” button for 5 seconds. 

•   If the audible signal is activated, a tone must sound and 

the “

Snd

” symbol must appear on the display for 3 

seconds. 

•   If the audible signal is deactivated, the “

Snd

” symbol 

must appear on the display for 3 seconds and no tone 
must sound.