31
Operation
The hood has an on-board controller which can also be used with the specific remote control (only supplied on some models)
Control panel on hood
T1.
Suction speed (power) control key.
Press repeatedly until the desired speed is selected, choosing between:
Speed
OFF
– LED
L1
: off
Speed
1
(low suction) – LED
L1
: green
light
LED L2
turns green and flashes if the delayed hood deactivation is enabled (only
with remote control).
Speed
2
(medium suction) – LED
L1
: yellow
light
LED L2
turns yellow and flashes if the delayed hood deactivation is enabled (only
with remote control).
Speed
3
(high suction) – LED
L1
: blue
light
LED L2
turns blue and flashes if the delayed hood deactivation is enabled (only
with remote control).
Speed
4
(intensive suction) – LED
L1
:
Blue button
Note
1:
Speed
4
has a limited duration of 5 min., and then the hood passes
automatically to speed
2
.
T2
Lighting control key (hob light - ambient light)
Press briefly for lighting the cooking hob
Press and hold longer to turn on and off and adjust the intensity of ambient light
Note
: ambient light is only available in some models.
Grease filter saturation warning - LED L1: red light
The warning is visible for about one minute after switching the hood off.
When this warning appears the grease filter
requires maintenance
.
Charcoal filter saturation warning - LED L1: red light
The warning is available for about one minute after switching the hood off.
When this warning appears the charcoal filter
requires maintenance
.
Deactivation/activation of charcoal filter saturation warning:
This warning is normally activated, to deactivate it:
with hood off, press keys
T1
and
T2
simultaneously until you hear a beep.
Release both keys and press the same keys again,
T1
and
T2,
shortly.
LED
L1
lights up steady with a red light (warning on) and then starts to flash
(warning off).
Repeat the operation if you want to reactivate the warning. LED
L1
switches
from flashing red (warning off) to a steady light (warning on).
Filter saturation warning reset
With the hood off, press keys
T1
and
T2
simultaneously for at least 5 seconds. LED
L1
will stop signalling saturation.
Repeat the operation in case of simultaneous warnings of both filters.
Remote control affiliation
The affiliation of the remote control is displayed with both LEDs on, which show
several colours in sequence.
Summary of Contents for Interstellar
