32
Automatic operation (sensor), connection with SNAP
®
Warning!
It is recommended to perform the
‘Adjusting the
parameters for automatic operation’
(see relevant
paragraph) before using the automatic mode and connect the
hood to the
SNAP
®
.
Automatic operation (sensor)
The hood will switch on at an adequate speed depending on
the cooking fumes detected by the hood sensor.
To activate this function:
Press keys
T1
and
T2
simultaneously. LED
L1
will light up
showing several colours, whereas LED
L2
will turn white.
Automatic operation of the hood with SNAP
®
Note:
SNAP
®
is an auxiliary suction unit capable of operating
together with the hood. For further information, refer to the
manual supplied with
SNAP
®
To activate this function:
Press keys
T1
and
T2
simultaneously. LED
L1
will light up
showing several colours, whereas LED
L2
will turn orange.
Adjusting the parameters for automatic operation.
Note:
All the calibration, selection, adjustment, and
logical connection operations described below are
possible with
hood OFF
and involve:
•
Hood calibration (automatic or manual).
•
Hob selection (gas - induction or electrical)
•
Logical connection between hood and
SNAP
®
(if in
possession of
SNAP
®
).
Sensor calibration
Note:
Calibration lasts about 5 minutes. LEDs
L1
and
L2
turn white and flash.
Calibration is required to allow the hood sensor to run
properly. Calibration can be:
Automatic:
every time the hood is reconnected to the mains (e.g.
upon first installation or after a blackout).
Manual:
To be carried out if unsatisfactory automatic operation is
detected and under normal kitchen conditions.
Press and hold key
T1
..
Hob
selection
(gas - induction or electrical)
Simultaneously press keys
T1
and
T2
until you hear a
beep
. Release the keys and press solely
T2
(within about
5 seconds) to access the hob selection mode..
Press T2 again to choose the required hob according to
the layout below:
Orange LED 2 Gas hob
Blue LED 2: Induction hob
White LED 2: electrical hob
The selected key remains on to indicate the selection.
After 10 seconds, the key flashes temporarily to indicate
that the selection made has been recorded.
Logical connection between hood and SNAP
®
(if in the
possession of SNAP
®
).
The connection between hood and SNAP
®
is automatic. No
setting is required.
Summary of Contents for Interstellar
