Elk ELK-M1EZ8 Installation Manual Download

Page: 25 / 68

M1EZ8 Installation and Programming

Page 25

[Effective w/Firmware 4.3.6]

12345678901234567890123456789012123

A1 11:=No

S t a y I n s t a n t S c r

12345678901234567890123456789012123

A1 12:=Yes

Night Scroll

12345678901234567890123456789012123

A1 13:=No

NightInstantScr

12345678901234567890123456789012123

A1 14:=No

StayChgIfArmed

If Yes, a Closing Ringback signal (otherwise known as closing report successful) will be
sent to all the keypads when the Communicator transmits a closing report and the Central
Station Receiver kissoff (acknowledgement) is received. The Exit Delay time will be
restarted at this time. The default value is No.

If Yes, the control can be armed by a single press of the Exit or Stay keys. No code is
required except to disarm.

Note: This option cannot be set to Yes if “Dbl Key Quick

Arm” (see below) is set to Yes.

The default value is Yes.

If Yes, the system can be armed by a double press of the Exit or Stay keys. The second
press must follow the first very quickly.

Note: This option cannot be set to Yes if “Sgl

Key Quick Arm” (see above) is set to Yes.

The default value is No.

If Yes, the Stay key may be pressed during the exit delay time to scroll (step) through the
selected levels of Stay arming. I.E. Stay Instant, Stay Night, etc. The options below
select the levels that will be available. The default value is Yes.

If Yes, AND option 10 is set to Yes, multiple presses of the Stay key during exit delay will
be able to scroll to the Stay Instant arming level. The default value is No.

If Yes, AND option 10 is set to Yes, multiple presses of the Stay key during exit delay will
be able to scroll to the Stay Night arming level. The default value is Yes.

If Yes, AND option 10 is set to Yes, multiple presses of the Stay key during exit delay will
be able to scroll to the Stay Night Instant arming level. The default value is No.

This option should be used with caution. If Yes, the Stay key may be used to scroll or
step the armed level after exit delay has expired and the control is fully armed. The
default value is No.

To program the text description of the Area (Name) press the left arrow key. Enter text
using the number keys. I.E. For a “K” press the 5 key twice. To move the cursor press
the right or left arrow keys. While programming the text, pressing the Chime key inserts
a space, and the Bypass key erases 1 digit. The up and down arrow keys toggle between
upper and lower case. Press the ELK key when complete.

Menu 03 - Area Definitions (continued)

12345678901234567890123456789012123

A1 15:AreaName

Area 1

12345678901234567890123456789012123

A1 09:=No

DblKeyQuickArm

12345678901234567890123456789012123

A1 10:=Yes

Stay Key Scroll

VACATION MODE

: During the exit delay time the Away key may be pressed to convert from Away mode to Away

Vacation mode. The Away Vacation mode does not alter any of the security arming times or zones. Its primary purpose
is for use with the Whenever/And/Then Rules programming of Elk-RP for enhanced energy savings modes.

AUTO ARMING

: The control has an Auto Arming feature which may be setup using the “Whenever/And/Then Rules” in

the ELK-RP PC Programming Software. Basically, a rule must be written to initiate the auto arm sequence at a specific
time and/or date occurrence along with a programmable pre-warning time period. At the end of the pre-warn time, the
system will automatically arm to the AWAY mode, bypassing any violated Burglar zones. All area keypad(s) will beep
and display a warning when the initiating time occurs. Pressing the * key clears this warning for 1 minute. The auto arm
time may be extended in 10 minute increments by pressing the RIGHT arrow key. No further warnings will occur until 10
minutes prior to the newly “extended” auto arm time.

Example

1: If a scheduled AutoArm is set for 06:00pm with a pre-

warn time of 20 minutes, the warning will start at 6:00pm and the auto arm will occur at 6:20pm. Pressing the RIGHT
arrow key to extend the time will cause the new auto arm time to be 6:30pm.

Area Definitions

Description of Option

12345678901234567890123456789012123

A1 08:=Yes

Sgl Key Quickarm

12345678901234567890123456789012123