Elk ELK-M1EZ8 Installation Manual Download

Page: 42 / 68

M1EZ8 Installation and Programming

Page 42

[Effective w/Firmware 4.3.6]

123456789012345678901234567890121234

SR01: 015=AC Fail
Rpt Delay - Min

123456789012345678901234567890121234

SR02: T=00 R=00

AC Fail Codes

123456789012345678901234567890121234

SR03: 00 = Auto

Test Code

Menu 12 - Sys Report Code Options & Codes

12345678901234567890123456789012123

12-Sys Rpt Code

Options & Codes

Sys Rpt Code Options

Description of Option

AC Fail Report Delay may be set to delay from 001 to 255 minutes. Valid range is 000 -
254 minutes. Default setting is 15 minutes. Setting this location to 255 results in no AC
failure annunciation at the keypad or by the dialer.

AC Fail T (Trouble) code will be reported upon AC failure, after any AC Fail Rpt delay time.
AC Fail R (Restore) will be reported immediately upon restoral of the AC power. Range is
00 to FF. Default is 00 (no report).

Auto Test code may be periodically reported to verify that the telephone line and internal
communications circuitry is functioning properly. Range is 00 to FF. Default is 00 (no
report).

Auto Test Hr:Min is normally set to occur during off-peak times. However, if may be set to
occur at any specific hour and minute. This location requires military time format. IE:
7:30 is AM while 19:30 is 7:30pm. Default is 00:00 which is Midnight.

Days Between Auto Test may be set to skip a certain number of days, from 1 to 255. The
default value is 000 which means that the test code, if programmed, will be reported every
day (24 hour interval) from the Auto Test time.

Aux. Overcurrent trouble (T) will be reported when the control’s auxiliary power is
overloaded. A restore (R) will be reported when the overload ceases. Range is 00 to FF.
Default is 00 (no report).

Exp Module Tbl T (Trouble) will be reported when an enrolled data bus module fails to
respond or is missing. Exp Module Tbl R (Restore) will be reported when the module is
restored. Range is 00 to FF. Default is 00 (no report).

This report code may be programmed in order to know when the Installer Level of
Programming has been entered. Range is 00 to FF. Default is 00 (no report).

This report code may be programmed to notify when Installer Level Programming is ended.
To prevent unnecessary reports, the report will not transmit until the * key is pressed three
times to signify final end of programming. The report will occur automatically at Midnight if
the * key sequence is not pressed. Range is 00 to FF. Default is 00 (no report).

Log 80% Full will be reported whenever the Event Log becomes 80% full. Range is 00 to
FF. Default is 00 (no report). The Elk-RP is required to download the log and/or clear it.

123456789012345678901234567890121234

SR04: =00:00

Auto Test Hr:Min

123456789012345678901234567890121234

SR05: 000=Days

Between AutoTest

123456789012345678901234567890121234

SR06: T=00 R=00

Aux Overcurrent

123456789012345678901234567890121234

SR07: T=00 R=00

Exp Module Tbl

123456789012345678901234567890121234

SR08: 00=Instal

Program Begin

123456789012345678901234567890121234

SR09: 00=Instal

Program End

123456789012345678901234567890121234

SR10: 00= Log

80% Full

Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.

System Report Codes and Options are global to the entire system such as Low Battery, AC Fail, etc. Using the up/down
arrow keys, select the appropriate option, then press the right arrow key to begin programming that option.

NOTE: Enter a two digit value to enable a report code. To disable a report code enter 00. When SIA or Contact ID is the
reporting format, the two digit value can simply be 01 since the control automatically produces the correct code
according to the SIA or Contact ID protocol. For 4+2 pulse format, enter a value from 01 to FF. To enter the A thru F
HEX characters press the RIGHT arrow key to position the cursor under the desired digit, then press the UP arrow (shift)
key once. Each press of the 2 key will now produce the following: 2, A, B, C. Each press of the 3 key will now produce
the following: 3, D, E, F. Press the RIGHT arrow key to cancel shift and move to the next character. See Appendix for
a summary of the SIA and Contact ID codes.

WWW.DIYALARMFORUM.COM