Elk ELK-M1EZ8 Installation Manual Download

Page: 45 / 68

M1EZ8 Installation and Programming

Page 45

[Effective w/Firmware 4.3.6]

Menu 14 - Wireless Definitions

WirelessDefinitions

Description

The Wireless Definitions menu is broken into four parts: 1:Receiver Options, 2:Xmitter
Options, 3:Xmitter Enroll, and 4:Keyfob Event Definitions. To program Receiver Options
press the right arrow key. To move to Transmitter Options, Xmitter Enroll, or Keyfob
Event Definitions press the up or down arrow keys.

R01: Receiver Size. Identifies the size of the connected Receiver so the appropriate
number of zones may be reserved. For the NX408E 8 zone receiver enter a 0, for a
NX416E 16 zone receiver enter a 1, for a NX448E 48 zone receiver enter a 2. The
Control will recognize these as wireless, starting from the ZnBank setting option.

R02:ZnBank Starting Zone. Identifies where the first wireless zone begins. Using the
receiver size and this starting number, the desired number of zones will be blocked out.
If another zone expander (hardwired) is encountered that results in a duplicate zone, the
Control will error tone and return to a 00 setting. To resolve the conflict: move the
starting zone to another setting, move the conflicting zone expander to another address,
or reduce the receiver size setting. Valid starting zones must be increments of 16:

Example: Entering a value of 2 for receiver size and 02 for starting zone would block out
48 zones from 17 thru 64 as wireless. NOTE: If an 8 zone receiver is installed, the upper
8 zones are not available (wasted) as far as the control is concerned. Receivers with
multiples of 16 zones (NX416E and NX448E) are therefore better economic choices.

R03: Reg. Supervision sets the interval, in hours, for “check-in” by transmitters which are
programmed for “Supervision Type 1”, see transmitter option 01. Valid range is 001 to
255 hours, however a value lower than 4 is not recommended. Default value is 24.

R04: Fire Supervision sets the interval, in hours, for “check-in” by transmitters which are
programmed for “Supervision Type 2” (Fire), see transmitter option 02. Valid range is 001
to 255 hours, however a value lower than 4 is not recommended. Default value is 004.

1234567890123456789012345678901212345

1:Rec Sel

Prg

Receiver Options

123456789012345678901234567890121234

RO2:=00 ZnBank

StartingZone xxx

1234567890123456789012345678901212345

RO3:=24 Hours

Reg. Supervision

1234567890123456789012345678901212345

RO4:=004 Hours

Fire Supervision

Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.

12345678901234567890123456789012123

1 4 - W i r e l e s s
Definitions

Requires

ELK-W035A

Wiring Assembly

Caddx Brand Receiver Board

White (n/a)

Brown (n/a)

NEG

AUX

+12V

Control Panel

Connect

to J3

A Data

Green

Red

Black

NX-408E
NX-416E
NX-448E

SET ALL FOUR ADDRESS

SWITCHES TO OFF!

Wiring Diagram for Caddx NX Receiver

The Control is compatible with the Caddx brand wireless receivers: NX408E (8 zones), NX416E (16 zones), and NX448E
(48 zones) and transmitters. Only 1 Receiver may be connected to the Control. A special 5 pin wiring harness (ELK-
WO35A) is required and it plugs into connector J3 “Aux Data Bus” located on the upper right side of the board.

123456789012345678901234567890121234

RO1:=0 Rec Size

0=8 ZoneReceiver

02=(Zone 17)

04=(Zone 33)

06=(Zone 49)

08=(Zone 65)

10=(Zone 81)

12=(Zone 97)

14=(Zone 113) 16=(Zone 129) 18=(Zone 145) 20=(Zone 161) 22=(Zone 177)

WWW.DIYALARMFORUM.COM