background image

© 14.11.2005 ELKA-Torantriebe GmbH u. Co. Betriebs KG              Page 38                                  TERRA 180/182 - 250/252 – 320/322 

 

12.2. Emergency mode 

 

In case a safety device (LSA, LSI, SLA or SLZ) is faulty, emergency mode is possible. 
After a warning time of 10 seconds, the gate can be moved in an emergency mode by 
using BA or BZ (dead man’s function). During the warning time as well as during the 
emergency mode the warning light is flashing. Emergency mode by radio remote control 
BT or BTG) is not possible due to safety reasons. 
 

 Warning

! Even when a safety device is faulty, the gate can be moved by BA and 

BZ. The buttons BA and BZ therefore have to be installed in such a way, that the 
gate can be seen during movement. 

 

Warning! 

Are external devices -giving a constant signal (e.g. timer) - connected to 

BA or BZ, these devices can activate the emergency mode and move the gate 
when a safety feature is faulty or active. 

 

Warning! 

In case the multi-functional relay is used for an additional radio remote 

channel, which is connected to BA or BZ, the emergency mode can be started by 
radio remote control. In this case only fixed transmitters should be used in such a 
way, that the gate can be seen during movement. 

 

13. Technical data MO36 
13.1. Selection range of Parameter and Original settings

 

 

Constant, not changeable values 

Parameter Original 

settings 

Time-lag before reactivating motor 

500ms 

Reversing for a short distance on obstacle 

500ms 

Time-lag before reversing 

200ms 

Max. running time limit   

500s 

Running time reserve during regular mode 

10s 

Warning time prior to emergency mode  

10s 

 

Changeable values 

Parameter 

Selection range 

Original settings 

Running distance 

Max. 32.000 Impulse 

3.000 Impulse 

Force 

1 - 99 

30 

Speed 

Level 1 - 8 

Level 8 

Time lag during opening 

0s - 9s 

2s 

Time lag during closing 

0s - 9s 

5s 

Stay-open time for both wings 

1s - 299s / OFF 

OFF 

Stay-open-time for pedestrian wing 

1s - 299s / OFF 

OFF 

Wind blast suppression 

0s - 9s 

0s 

Warning prior to opening 

0s or 4s 

0s 

Warning prior to closing 

0s or 4s 

0s 

Pressure relief of  
electromagnetic bolt 

0s / 1s / 2s / 90s 

0s 

Multi-functional relay 

Push button mode / Toggle 
mode / Light pulse / 3-minute-
light 

Push button mode 

LS lockage function 

ON / OFF 

OFF 

Photo-cell function 

L1 or L2 or L3 

L1 

Number of wings 

1 / 2 

Photo-cell testing 

ON / OFF 

OFF 

Type of safety contact profile 

8,2k

 or FRABA 

8,2k

 

Radio remote control code BT 

X-code 

- + - + - + - + - 

All other radio remote control codes 

X-code 

deleted 

 

Summary of Contents for TERRA 180







































Reviews: