background image

Troubleshooting.

page 11

Problem: 

Fan fails to operate.

Solutions:

1. Check power to wall switch/wall control.
2. Check to be sure code switches in remote control 
transmitter and wall control are set properly.
3. Verify that wall control is wired properly.
4. Check to be sure fan is wired properly.
5. Learning process between fan, remote control 
transmitter and wall control may not have been 
successful and code was not activated. Turn off power and 
repeat instructions for SET button in Section 10 (page 9).
 

Problem: 

Light kit not lighting.

Solutions:

1. Check wall switch to fan.
2. Check that wires in canopy are wired properly.
3. Check to be sure code switches are set properly in 
remote control transmitter and wall control.
4. Verify that male and female plugs are connected 
properly in fitter plate.
5. Learning process between fan, remote control 
transmitter and wall control may not have been 
successful and code was not activated. Turn off power and 
repeat instructions for SET button in Section 10 (page 9).
 

Problem: 

Fan operates but light fails.

Solutions: 

1. Check to be sure wires in canopy are wired properly.
2. Verify that male and female plugs are connected 
properly in fitter plate.
 

Problem: 

Fan and light fail to operate with remote 

control or wall control.

Solutions:

1. Check battery power to remote control.
2. Check to be sure code switches are set properly in 
remote control transmitter and wall control.
3. Learning process between fan, remote control 
transmitter and wall control may not have been 
successful and code was not activated. Turn off power and 
repeat instructions for SET button in Section 10 (page 9).
 

Problem: 

Fan wobbles.

Solutions:

1. Use the balancing kit provided in one of the hardware 
packs. 

If no blade balancing kit is provided, please call 

Customer Support, 1-800-486-4892, to request one.

2. Check to be sure set screw(s) on motor housing yoke is 
(are) tightened securely.
3. Check to be sure set screw on hanging ball is tightened 
securely.

Warranty.

Parts Replacement.

For parts and information, please refer to
"Parts Inventory" on page 2.
Ellington Customer Support:

1-800-486-4892

www.craftmadebrands.com

WARNING: 

Failure to disconnect power supply prior to 

troubleshooting any wiring issues may result in serious 
injury.

CRAFTMADE/ELLINGTON LIFETIME WARRANTY:
CRAFTMADE/ELLINGTON warrants this fan to the original 
household purchaser for indoor use under the following 
provisions:
1-YEAR WARRANTY: CRAFTMADE/ELLINGTON will replace 
or repair any fan which has faulty performance due to a 
defect in material or workmanship. Contact 
Craftmade/Ellington Customer Service at 

1-800-486-4892

 

to arrange for return of fan. Return fan, shipping prepaid, to 
Craftmade/Ellington. We will repair or ship you a 
replacement fan, and we will pay the return shipping cost.
5-YEAR WARRANTY: CRAFTMADE/ELLINGTON will repair or 
replace at no charge to the original purchaser any fan 
motor that fails to operate satisfactorily when failure 
results from normal use.
RETURN FAN MOTOR ONLY, shipping prepaid, to 
Craftmade/Ellington. We will repair or ship purchaser a 
replacement motor and Craftmade/Ellington will pay the 
return shipping cost.
6-YEAR to LIFETIME LIMITED WARRANTY: 
CRAFTMADE/ELLINGTON will repair the fan, at no charge 
for labor only to the original purchaser, if the fan motor 
fails to operate satisfactorily when failure results from 
normal use. Parts used in the repair will be billed to the 
purchaser at prevailing prices at time of repair.
    The purchaser shall be responsible for all costs incurred 
in the removal, reinstallation and shipping of the product 
for repairs.
    This warranty does not apply when damage from 
mechanical, physical, electrical or water abuse results in 
causing the malfunction. Deterioration of finishes or other 
parts due to time or exposure to salt air is specifically 
exempted under this warranty.
    Neither Craftmade/Ellington nor the manufacturer will 
assume any liability resulting from improper installation or 
use of this product. In no case shall the company be liable 
for any consequential damages for breach of this, or any 
other warranty expressed or implied whatsoever. This 
limitation as to consequential damages shall not apply in 
states where prohibited.

Summary of Contents for TRD60PLN4

























Reviews: