background image

 

 

1. Press 

+

 and 

-

 at the same time to enter the menu. 

2. Step to 

INTERNAL

 with 

M

.

  

3.  Set the number of samples (1 - 36) per hour with 

+

 and 

-

.  

4. Confirm with 

=

.

 

5.  Choose between FLon and FLoF. Use

 

+

.

 

6.  Confirm and start sampling with 

=

.

 

7.  When FLon is chosen the display shows "IntF" until the level sensor is activated.

 

4.1.2 External control 

 
External controlled sampling is performed after pre-setting of the parameters that effects the sampling 
frequency. 
 
External control device is connected through the Amphenol-contact at the lower side of the sampler.  

 
A. Flow control sampling 

 
Samples are taken in proportion to the flow; the sampler gets a signal from a flow meter. 
 

1. Press 

+

 and 

-

 at the same time to enter the menu 

2. Step to 

MAX FLOW

 with 

M

.  

3.  Set the numeric value of the actual max flow with 

+

 and 

-

 keys, keep the key pressed to accelerate 

the numeric updating.  

4. Confirm with 

=

 

(the display flashes).  

5.  Stop the flashing with 

+

 or 

-

. Put the decimal point at the correct place with 

+

 (at the left) and

 

-

 

(at the right). 

6. Confirm with 

=

.

 

7.  The sampler steps automatically to 

INTERVAL

.

 

8.  Set the numeric value of the interval, number of m³ between samples, with 

+

 and 

-

 keys keep the 

key pressed to accelerate the numeric updating  

9. Confirm with 

=

 

(the display flashes).  

10. Stop the flashing with 

+

 or 

-

. Put the decimal point at the correct place with 

+

 (at the left) and

 

-

 

(at the right). 

11. Confirm with 

=

.

 

 

NOTE! Control that the interval < max flow, and that max flow / interval not exceeds 36 samples/h. 

 

12. The sampler steps automatically to 

MAN SAMPLE

.

 

13. Step to 

ANALOG

 with 

M

14. Set the signal range (0 - 20 mA alt. 4 - 20 mA) with 

+

 key. 

15. Confirm and start sampling with 

=

 

(the display shows the actual flow in % of max flow).

 

 
Example of settings at flow controlled sampling  

Ex.1 

Max. flow 

5,5 m

3

/h 

Interval 2 

m

3

 between samples 

 
The sampler takes samples according to 5,5/2 = 2,75 samples/h, one sample every 22nd minute at max. flow. 

 
Ex.2 

Max. flow 

3,6 m

3

/h 

Number of samples  3 samples/h 
 

Summary of Contents for VA/V3
















Reviews:

Related manuals for VA/V3