background image

 

FOR UNITED STATES USERS: 
INFORMATION

 

This equipment has been tested and found to comply with the limits for a Class A digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference when the equipment is operated in a 
commercial environment.   
This equipment generates, uses, and can radiate radio frequency energy and, if not 
installed and used in accordance with the instruction manual, may cause harmful 
interference to radio communications. Operation of this equipment in a residential area is 
likely to cause harmful interference in which case the user will be required to correct the 
interference at his own expense.   

 

USER-INSTALLER 
CAUTION:

 

Your authority to operate this FCC verified equipment could be voided if you make changes 
or modifications not expressly approved by the party responsible for compliance to Part 15 
of the FCC rules. 

 

 

 

 

 

 

 

 

 

 

 

 

 

WARNING 

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS 
PRODUCT TO RAIN OR MOISTURE. 

 
The connection of a non-shielded equipment interface cable to this equipment will 
invalidate the FCC Certification or Declaration of this device and may cause interference 
levels which exceed the limits established by the FCC for this equipment. It is the 
responsibility of the user to obtain and use a shielded equipment interface cable with this 
device. If this equipment has more than one interface connector, do not leave cables 
connected to unused interfaces. Changes or modifications not expressly approved by the 
manufacturer could void the userʼs authority to operate the equi

pment. 

Summary of Contents for OX-1





















Reviews: