background image

 

5

 

USAGE PRECAUTIONS 

 

Be sure to use the supplied USB cable. 

 

The supplied USB cable is designed for exclusive use with this product. Do not use it with other 
products. 

 

Be careful not to pinch your finger when you move the arm. 

 

When storing the product, do not leave it under direct sunlight or by heaters. It may be discolored, 
deformed, or damaged. 

 

Do not place the product in any humid, dusty, salt bearing wind, or vibrating locations. 

 

Use it under the following environmental conditions: 
Temperature

0

40

   

Humidity

30

%〜

85

(No condensation)   

 

Use a soft, dry cloth for cleaning.

 

Do not use any volatile solvent such as thinner or benzene. 

 

Luminescent and Black Spots 
There may be some pixels that do not properly operate due to the use of CMOS Area Image

 

Sensors made-up of many pixels. 
Though luminescent or black spots may be found on the screen, it is a phenomenon peculiar to the 
CMOS Area Image Sensors and is not a malfunction. 

 

Follow the guidelines below to prevent the product from dropping or overturning. 
- Use the product on a stable base, desk, or table. Do not place the product on an unstable base or 

slanted location. 

- Place or wire the product so as to prevent the cables from being pulled or drawn. 

 

Do not point the lens directly to the sun. It could degrade the imaging capability. 

 

Do not look directly into the LED light. If you look directly into it at pointblank range, your eyes may 
be injured. 

 

ELMO is not liable for any damage caused by the loss or damage of the data transferred to a 
computer by using the USB cable and recorded by using a capturing software. 

 

If the product is used for longer than the warranty period, its performance and quality may 
deteriorate due to the lifetime of its parts. For parts replacement (on chargeable basis), consult the 
dealer from whom you purchased this product or contact us from the following website: 

https://www.elmousa.com        https://www.elmoeurope.com 

 

Copyright 
Unless used for personal use, it is prohibited strictly under copyright law to use any photo files 
without the prior consent of the copyright holder. Even if using for personal use, be careful that 
there could be a situation where video or audio recording is restricted or illegal. 

 

The contents of this document are subject to change without notice. The latest version is available 
from the following official websites:   

https://www.elmousa.com        https://www.elmoeurope.com 

 

It is prohibited under copyright law to use or copy any part or the whole of this document without 
our prior written consent. 

 

ELMO shall not be liable for any claim for damage or loss of earnings or any claim raised by a 
third person due to the use, malfunction or repair of the product.

Summary of Contents for OX-1





















Reviews: