23
OPERATION
TURN ON THE POWER SWITCH
WHILE PRESSING THE “–” OF
STITCH WIDTH BUTTON AND “+”
OF STITCH LENGTH BUTTON.
PRESS THE “+” OF STITCH
LENGTH BUTTON 5 TIMES
WITHIN 2.5 SECONDS TO
SELECT 6.
PRESS THE “–” OF STITCH
WIDTH BUTTON. “01.” WILL BE
DISPLAYED ON THE LED FOR 1
SECOND.
PRESS THE “–” OF STITCH
WIDTH BUTTON. ”02.” WILL BE
DISPLAYED ON THE LED FOR
1 SECOND.
PRESS THE “–” OF STITCH
WIDTH BUTTON. ”03.” WILL BE
DISPLAYED ON THE LED FOR
1 SECOND. PRESS THE
BUTTONS FROM S1 TO S8.
PRESS THE “–” OF STITCH
WIDTH BUTTON. ”04.” WILL BE
DISPLAYED ON THE LED FOR
1 SECOND.
• MOVE THE BOBBIN WINDER
TO THE RIGHT.
• MOVE THE BOBBIN WINDER
TO THE LEFT.
PRESS THE “–” OF STITCH
WIDTH BUTTON. “05.” WILL BE
DISPLAYED ON THE LED FOR
1 SECOND.
• SKIP THIS STEP.
PRESS THE “–” OF STITCH
WIDTH BUTTON. “06.” WILL BE
DISPLAYED ON THE LED FOR
1 SECOND.
• PULL DOWN THE BUTTONHOLE
LEVER.
• PUSH AND PULL THE
BUTTONHOLE SENSOR.
CORRECT RESULTS
• BEEP SOUNDS WHEN BUTTONS
ARE PRESSED.
• LED DISPLAYS “8.8.” AND BLINKS
IN 1-SEC. INTERVAL.
• LED DISPLAYS “Ld” AND BLINKS
IN 1-SEC. INTERVAL.
• LED DISPLAYS “– –” AND BLINKS
IN 1-SEC. INTERVAL.
• LED DISPLAYS PRESSED
BUTTON #.
• LED DISPLAYS “– –”
• LED DISPLAYS THE # OF
BUTTON. (S1 TO S8)
• LED DISPLAYS “ || ”
OR “ ] [ ”.
• LED DISPLAYS “UP” OR “DOWN”.
• PULL THE BUTTONHOLE
LEVER TO THE FRONT.
• RELEASE THE
BUTTONHOLE LEVER
(CENTER POSITION)
• PUSH THE BUTTONHOLE
LEVER TO THE REAR.
LED
LED LAMP
BUTTONS
BOBBIN
WINDER
SPINDLE
PRESSER
FOOT
LIFTER
* NOT
APPLICABLE
FOR THIS
MACHINE
BUTTONHOLE
SENSOR
DEFECTIVE RESULTS
• NO BEEP SOUND
• DOES NOT ENTER
SELF-DIAGNOSTIC
MODE.
• LCD AND LED DOES
NOT BLINK.
——————————
REPLACE OR ADJUST
• REPLACE THE
PRINTED BOARD A.
• LED DOES NO
BLINK.
——————————
REPLACE OR ADJUST
• REPLACE THE
PRINTED BOARD A.
• LED DOES NOT
DISPLAY THE # OF
PRESSED BUTTON.
——————————
REPLACE OR ADJUST
• REPLACE THE
PRINTED BOARD A.
• LED DOES NOT
DISPLAY AS
ILLUSTRATED.
——————————
REPLACE OR ADJUST
• ADJUST THE BOBBIN WINDER
SWITCH POSITION.
• REPLACE THE BOBBIN WINDER
SWITCH SPINDLE
• REPLACE THE PRINTED
BOARD A.
• LED DOES NOT
DISPLAY AS
ILLUSTRATED.
——————————
REPLACE OR ADJUST
• REPLACE OR ADJUST
THE BUTTONHOLE
SENSOR.
• REPLACE THE
PRINTED BOARD A.
ＬＥＤ
ＬＥＤ
（S１）
（S８）
S5 S6 S7 S8
S1 S2 S3 S4
q
LEFT
POSIITON
w
RIGHT
POSIITON
q
w
SELF DIAGNOSTIC TEST
SELF DIAGNOSTIC TEST
SELF DIAGNOSTIC TEST
SELF DIAGNOSTIC TEST
SELF DIAGNOSTIC TEST
Summary of Contents for 6200 -
Page 1: ......
