background image

ELSEMA 

4G Receiver with relay output, G-2025 

 

 

Page

 

1

 

 

www.elsema.com

 

 

G-2025 

4G receiver with relay output for opening sliding, swing gates, doors or switching devices

 

Features 

 

Up to 999 users  

 

4G network compatible 

 

Built-in battery back-up 

 

Setup with easy to use PC software 

 

Switches relay with free call from mobile phone  

 

Digital inputs for sensors or switches 

 

SMS confirmation of relay switching 

 

Secure password protected 

 

Only authorized numbers can operate the G-2025 

 

Operates from anywhere if 4G network is available. Unlimited range! 

 

12 Volts DC power pack included 

 
Application 

 

Open / close gates, doors, shutters, garage doors with a free call! 

 

Security alarm, On/Off lights, pumps and machines. 

 
Description 

The G-2025 can have up to 999 authorized users and uses the 4G Telstra and Vodafone network for 
communication (Not compatible with Optus). All you need is to insert a valid SIM card and program phone 
numbers of all users using the PC software or through simple SMS text commands. When an authorized user 
makes a call to the receiver, it rejects the call and activates a relay. Since the call is rejected the user is not 
charged for the call.  
 
There are 2 digital inputs available. These 2 inputs can be wired to motion sensor (PIR), smoke detectors, reed 
switch, windows, or any other type of voltage free contact. The GSM Receiver can be programmed to send 
different SMS messages for each input.   
 
A 12 Volt output is also available on the GSM Receiver which can activate a 12 VDC siren or warning light 
when either of the input is activated. (Refer to the wiring diagram) 
 
The G-2025 works on 4G network therefore the receiver can be activated from anywhere in the country where 
4G mobile network is available. For example, you can open your gate or switch on your kitchen lights in 
Sydney from Melbourne by making a call from your mobile phone.  
 
 
 
 
 
 
 
 

 

12 Volts DC Power Pack Included 

Summary of Contents for G-2025















Reviews: