background image

MISSION 1K●2K●3K 

SINGLE PHASE

 

Rev. 02 

– 19 March 2015

 

 

1.  SAFETY INSTRUCTION 

This  chapter  mainly  introduce  the  safety  marks  and  notes  of  MISSION  1KVA-2KVA-3KVA  series  on-line  UPS. 
Read this chapter carefully before operating on the equipment. 

 

1.1 Safety instruction 

 
There  is  dangerous  voltage  and  high  temperature  inside  the  UPS.  During  the  installation,  operation  and 
maintenance,  please  abide  the  local  safety  instructions  and  relative  laws,  otherwise  it  will  result  in  personnel 
injury  or  equipment  damage.  Safety  instructions  in  this  manual  act  as  a  supplementary  for  the  local  safety 
instructions. 
Our  company  will  not  assume  the  liability  that  caused  by  disobey  of  safety  instructions.  Please  note  the 
following: 
1. 

Don’t use the UPS when the actual load exceeds the rated load. 

2.  There are high-

capacity batteries in the standard type UPS. You mustn’t open the enclosure or it will lead to 

electric shock. If it needs internal maintenance or battery replacement, please send it to the designated site. 

3.  Internal short-

circuit of the UPS will cause electric shock or fire. So don’t place the containers equipped with 

liquid on the top of the UPS so as not to cause danger of electric shock and so on. 

4. 

Don’t put the UPS in a place with high temperature or humidity as well as the corrosive gas, much dust. 

5.  Keep good air circulation between in-vent on front panel and out-vent on back panel. 
6.  Avoid direct sunlight or near heat-dispensed objects. 
7.  In case that the smoke appears on the UPS, please cut off the power as soon as possible and contact the 

dealer service site. 

 

1.2 Symbols indication 

 
The  safety  symbols  cited  in  this  manual  are  shown  in  table  1-1,  which  are  used  to  inform  readers  of  safety 
issues that should be obeyed when installation, operation and maintenance. 
 

Safety Symbol   

Indication 

 

Attention 

 

 

Static discharge sensitive 

 

Electric shock 

Table 1-1 

 
There are three levers of safety grade: Dangerous, Warning and Attention. The remark is on the right side of the 
safety symbol, the detailed comments is behind, shown as following:   
 
 

 

   

Dangerous: 

Indicate risk of serious injury or death or seriously damage the equipment 

 

   

Warning: 

Indicate risk of serious injury or damage the equipment. 

 

   

Attention: 

Indicate risk of injury or damage the equipment. 

 

Summary of Contents for MISSION 1000



























Reviews: