background image

 

10

 

ESR series routers

 

Table 2.8 - System indicator states 

Indicator 

name 

Indicator functions 

Indicator state 

Device state 

Status 

Currency device indicator. 

Green 

Device operates properly. 

Orange 

Device is in the software loading state  

Alarm 

Existence and device emergency 
level indicator 

VPN 

Active VPN-session indicator.

 

 

Flash

 

Indicator of active exchange with 
data storages (SD-card or USB 
Flash). 

Orange 

Carrying out read/write operation by 
«copy» command 

Power 

Device power indicator. 

Green 

Device power supply is proper. Primary 
power supply, if it is installed, operates 
properly. 

Orange 

Disability of primary power supply, 
primary network fault or default.  

Off 

Fault of the device internal power 
supplies. 

Master

 

Operation indicator in failover -
modes.

 

Fan 

Emergency indicator of fans  

Off 

All fans are operational. 

Red 

One or more fans failed. The cause of 
emergency may be fault of even one 
fan (for example, stopping or under-
frequency rotation). 

RPS

 

Reserve power supply operation 
mode. 
 

Green 

Reserve power supply is installed and 
in normal operation. 

Off 

Reserve power supply is not installed. 

Red 

Reserve power supply is missing or 
failed 

Summary of Contents for ESR-100




















Reviews: