ELTEX ESR-100 Quick Start And Installation Manual Download

Page: 9 / 19

ESR series routers

2.3.

Light indication

ESR-1000 light indication

Metal interfaces state of GigabitEthernet is represented by two LED indicators:

LINK/ACT

- green

and

SPEED

-amber:

Figure 2.11 -

RJ-45 socket appearance

SFP-interface status is represented by two RX/ACT and TX/ACT indicators:

Figure 2.12 - Optical interfaces' indicators

Table 2.6 - Light state indication of metal interfaces and SFP- interfaces

SPEED indicator is lit

LINK/ACT indicator is lit

Ethernet interface state

Off

Port is disabled or connection is not
established

Off

Solid on

10Mbps or 100Mbps connection is
established

Solid on

1000Mbps connection is established

Flashes

Data transfer is in progress

Table 2.7 - SFP/SFP+ interfaces states light indication

Glowing of RX/ACT

indicator

Glowing of TX/ACT

indicator

Ethernet interface state

Off

Port is disabled or connection is not
established

Solid on

Connection is established

Flashes

Receive data is in progress

Flashes

Data transfer is in progress

LINK/ACT

SPEED

RX/ACT

TX/ACT

Summary of Contents for ESR-100




















Search results

Summary of Contents for ESR-100

Reviews:

Related manuals for ESR-100

Brands by name

Popular brands

ELTEX ESR-100, Quick Start And Installation Manual

Search results

Summary of Contents for ESR-100

Reviews:

Related manuals for ESR-100

Brands by name

Popular brands