background image

 

103 

 

Fig. 25.4 – Service Model 2 Chart 

Dedicated  S-VLANs  are  used  between  the  OLT  and  service  routers  (BRAS,  VoIP  SR)  for  each  of  the 

following services: VoIP,  Internet, IPTV unicast,  and TR-069. These S-VLANs are  common for all subscribers 
(ONTs). Corresponding GEM ports are created for every OLT service between the ONTs and OLT. A dedicated 
MC-VLAN is used for multicast transmissions. 

OLT transmits S-VLAN into a corresponding U-VLAN for each service. An ONT associates the U-VLAN with 

corresponding ONT interfaces or program modules. For example, the TR-069 service is associated with a TR-
069  client  with  the  help  of  a  corresponding  interface.  The  VoIP,  Internet,  and  IPTV  unicast  services  can 
operate in the "router" or "bridge" modes depending on the ONT configuration. The chart shows all services 
configured in the "router" mode. 

All  broadcast  and  unknown  unicast  traffic  is  redirected  to  a  dedicated  broadcast  GEM  port  in  this 

model.  Broadcast  and  unknown  unicast  packets  are  sent  to  U-VLAN  (for  the  VoIP,  Internet,  and  IPTV 
unicast services) in the ONT. 

In general, this model is similar to Model 3 except the following: transmission of C-VLAN to U-VLAN 

is performed on the OLT side, while the VoIP, Internet, and IPTV unicast traffic comes to U-VLAN in the 
ONT. 

Thus,  the  model  implements  "VLAN  for  Service"  for  the  VoIP,  Internet,  IPTV  unicast,  and  TR-069 

services. 

25.1.3

 

Model 3 

Consider an example of Model 3 implementation. 

The chart of this service model is shown in Fig. 25.5. 

Dedicated S-VLANs are used between the OLT  and service  routers (BRAS, VoIP SR) for each of the 

following  services:  VoIP,  Internet,  IPTV  unicast,  and  TR-069.  These  S-VLANs  are  common  for  all 
subscribers (ONTs). Corresponding GEM ports are created for every OLT service between the ONTs and 
OLT. A dedicated MC-VLAN is used for multicast transmissions. 

The VoIP, Internet, IPTV, and TR-069 unicast services are associated with S-VLAN in an ONT. The ONT 

transmits  S-VLAN  into  a  corresponding  U-VLAN  for  each  service.  The  ONT  associates  the  U-VLAN  with 
corresponding ONT interfaces or program modules. For example, the TR-069 service is associated with a 
TR-069 client with the help of a corresponding interface. The VoIP, Internet, and IPTV unicast services 

Summary of Contents for LTP-4X








































































































































































































Reviews: